JI CASE ENGINEERING PARTS LIST PART . L.C.E. 1341161CI HDT 12JAN H. SCRIPTION WELDMENT. SHUTTLE SHAFT 2 HOUSING SCREW PIN SCREW SCREW ххх SHAFT SHUTTLE CLUTCH. 6 PLATE SET. 5/16-18 UNC X 3/8 ROLL. 1/8 X 1/4 SET. ORIFICE SET. 1/2-13 UNC X 3/8 A188207 178-440 1 38-294 5 A183506 6 178-479 XXX END OF DATA THESE SURFACES TO BE CLEAN AND FREE OF WELD SPLATTER BOTH SIDES 109.41 TYP END OF PINS TO BE 0.5-1.5 BELOW O.D. OF SHAFT + Ø0.20A® eø0.20B& NOTES: EB OR LB WELD. CASE ES-A6919 DRILLED PASSAGES MUST BE CLEAN AND FREE OF FOREI GN MATERIAL BEFORE PLUGS ARE INSTALLED 3 MIN WELD DEPTH TYP BOTH SIDES WELD BEAD TO BE CENTERED ON JOINT WITHIN 0.1 INSTALL ALL SET SCREWS WITH JI CASE 345-71 THREAD SEALANT (LOCTITE 277) AFTER CLEANING AND WELDING ALL WELD JOINTS TO BE AIR/OIL TI GHT UP TO 3448 kPa (500 PSI) APPLIED PRESSURE MUST BE CLEAN AND FREE OF BURRS JT Case Witconsin 53404 FSCH 10988 B NC 7590 | CAD AT HDT METRIC 32479 DEMERSIORS ARE IN LLINETS SURFACE ROUGHNESS IN MICROMETHES SHAFT-WELDMENT. SHUTTLE SEPT RAEN STS INE 12JAN 17JAN FOSEE A RELEASE FOR PRODUCTION VMP INFED C890321 FULL RLISFER ETRIC TOLERANCES UNLESS OTHERNISE SPECIFIED nee E cr EN AI88551 * e PLACE sectLS 0.laAs SEMENSTOS 134|161CI ONE PLACE DECTIALS Ferm Na. F260E 6. 10 12

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter37: Clutches

Section: Chapter Questions

Problem 14RQ: The surface of the pressure plate contacts the. a. transmission main shaft b. throwout bearing c....

See similar textbooks

Related questions

Concept explainers

Question

I need these three parts answered pertaining to the print provided below.

What geometric term applies in a general way to the main objects of this assembly, whichis a primary reason only one view is required? (Multiple Choice)
a. Perspective
b. Planar
c. Two Dimensional
d. Cylindrical

What type of section describes this one-view drawing? (Multiple Choice)
a. Broken out
b. Partial
c. Half
d. Full

During what month was this drawing released for production as revision A? (Multiple Choice)
a. January
b. March
c. May

JI CASE ENGINEERING PARTS LIST PART .
L.C.E.
1341161CI
HDT 12JAN
H.
SCRIPTION
WELDMENT. SHUTTLE
SHAFT
2 HOUSING
SCREW
PIN
SCREW
SCREW
ххх
SHAFT
SHUTTLE
CLUTCH. 6 PLATE
SET. 5/16-18 UNC X 3/8
ROLL. 1/8 X 1/4
SET. ORIFICE
SET. 1/2-13 UNC X 3/8
A188207
178-440
1 38-294
5 A183506
6 178-479
XXX END OF DATA
THESE SURFACES TO BE CLEAN
AND FREE OF WELD SPLATTER
BOTH SIDES
109.41
TYP
END OF PINS TO BE 0.5-1.5
BELOW O.D. OF SHAFT
+ Ø0.20A®
eø0.20B&
NOTES:
EB OR LB WELD.
CASE ES-A6919
DRILLED PASSAGES MUST BE CLEAN AND
FREE OF FOREI GN MATERIAL BEFORE
PLUGS ARE INSTALLED
3 MIN WELD DEPTH
TYP BOTH SIDES
WELD BEAD TO BE
CENTERED ON JOINT
WITHIN 0.1
INSTALL ALL SET SCREWS WITH JI CASE 345-71
THREAD SEALANT (LOCTITE 277) AFTER CLEANING
AND WELDING
ALL WELD JOINTS TO BE AIR/OIL TI GHT
UP TO 3448 kPa (500 PSI) APPLIED PRESSURE
MUST BE CLEAN AND FREE OF BURRS
JT Case
Witconsin 53404
FSCH
10988 B
NC 7590
| CAD AT HDT
METRIC
32479
DEMERSIORS ARE IN LLINETS
SURFACE ROUGHNESS IN MICROMETHES
SHAFT-WELDMENT. SHUTTLE
SEPT RAEN STS
INE 12JAN
17JAN FOSEE
A RELEASE FOR PRODUCTION
VMP INFED
C890321
FULL RLISFER
ETRIC TOLERANCES UNLESS OTHERNISE SPECIFIED nee E cr
EN
AI88551
* e PLACE sectLS
0.laAs SEMENSTOS
134|161CI
ONE PLACE DECTIALS
Ferm Na. F260E
6.
10
12

Expert Solution

Trending now

This is a popular solution!

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions