Lazuli. A radially uniform pen with a cross sectional area of a regular ~octagon was placed on a incline as shown in the figure. Provided that there is enough static friction to keep the pen from sliding down, what is the maximum possible angle before the pen starts rolling? O 30° O 22.5° 1 O 45° O 60° YX X X X X

Lazuli. A radially uniform pen with a cross sectional area of a regular ~octagon was placed on a incline as shown in the figure. Provided that there is enough static friction to keep the pen from sliding down, what is the maximum possible angle before the pen starts rolling? O 30° O 22.5° 1 O 45° O 60° YX X X X X

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.73P

See similar textbooks

Similar questions

Three cylinders A:B:C rolling in external contact has a speed ratio of 4:2:1. If the diameter of cylinder A is 10 cm, find the center distance between cylinder A and C.
Find the relationship between the cross slide and compound rest in order to machine a taper value that is 18.4349º. Support your answer by sketch.
Which is the most appropriate force diagram at point A? Answer quickly. Will upvote.
Answer the 2 questions and I'll upvote. Thank you. 5-23. Determine the force P required to cause the wedge in Fig. P5–23 to start to move downward, knowing that µs = 0.30 at all contact surfaces. 5-25. The 10° wedge in Fig. P5–25 is used to split a log. The coefficient of static friction between the wedge and the wood is 0.30. If a force P = 500 lb is needed to drive the wedge into the wood, determine the force exerted on the log by the wedge after it has been driven into the log.
Dyanmics Engineering review Part B Determine the normal force of the rod on the collar at B. Express your answer to three significant figures and include the appropriate units. N = Part C Determine the rate of increase in collar's speed at B. Express your answer to three significant figures and include the appropriate units. a =
1-)The diagram of the change of cutting force for the cutting work performed with the press seen in the figure is given in the figure Engine revthe number is 900 rpm and the number of Flywheel revolutions is 60 rpm.The moment of inertia of the rotating masses in the engine is 0.35 kgm^2. Speedcalculate the moment of Flywheel inertia required for the press so that its smoothness is 0.01 . Engine power is 1.5 kWit is known
arrow_forward Question PROBLEM The diameter of two pulleys are (0.3m)and (0.2m), center distance (1m).if we use open belt drive. Determine: 1- the length of V-belt (2ß = 60°). 2- the contact angle between belt and smaller pulley. 3- the horse power, if the smaller pulley turn with speed (400r.p.m) and the tension force in tight side (T1=900N), coefficient of friction ų=0.3 4- the speed of large pulley.
. During the operation of a punch press, its flywheel decelerates uniformlyfrom 400 rpm to 200 rpm in l sec. The rim of the flywheel weighs 1288 lb, itsinside and outside diameters are 56 in. and 60 in., and it is attached to itshub by 6 spokes. What average shearing force is developed between the rim andeach spoke during the 1 sec interval?
Determine the nternal force BG. Format of the answer is lb.
Gentlemen, please help to solve a,b,c as I faced confusing questions about screw jack. Conditions are: screw jack is lifting 3.2 tonnes, screw pitch is 12 mm, diameter of the screw is 5 mm. Coefficient of friction was not given but I think we will need it for total force calculation, lets take it 0.2. a) Calculate horizontal component to move the load - what is ment here by horizontal component? b) Calculate vertical component to move the load - what is ment here by vertical component? c) Total force needed to move the load with a lever of 0.82m d) Velocity ratio (VR=distance by effort/distance by load) Distance by effort (lever)=2 x 3.14 x 0.82 = 5.15m Distance by load = pitch= 12mm= 0.012 m VR=5.15/0.012= approx 429. e) Calculate efficiency. For this we need to have MA (mechanical advantage). It can be calculated when we know total force. Efficiency=Load (3200 x 9.8) / effort
What is the answer in #3B. Show complete solution and FBD
can you create or provide illustration or example of actual situations with curvilinear motions.