lon exchange is used to remove water hardness of a well water, which has a total hardness of 450 mg/L as CaCO3. The ion exchanger has leakage hardness of 15 mg/L as CaCO3. The percentage of water that is bypassed and blended is 30%. What is the final water hardness in the finished or treated water most nearly? O 105 mg/L as CaCO3 O 110 mg/L as CaCO3 125 mg/L as CaCO3 O 150 mg/L as CaCO3

lon exchange is used to remove water hardness of a well water, which has a total hardness of 450 mg/L as CaCO3. The ion exchanger has leakage hardness of 15 mg/L as CaCO3. The percentage of water that is bypassed and blended is 30%. What is the final water hardness in the finished or treated water most nearly? O 105 mg/L as CaCO3 O 110 mg/L as CaCO3 125 mg/L as CaCO3 O 150 mg/L as CaCO3

EBK A SMALL SCALE APPROACH TO ORGANIC L

4th Edition

ISBN:9781305446021

Author:Lampman

Publisher:Lampman

Chapter13: Isolation Of Eugenol From Clov

Section: Chapter Questions

Problem 9Q

See similar textbooks

Similar questions

Prepare 1500mL of 0.5N H2SO4 solution with specific gravity of 1.84g/mL and assay of 97%. Write complete solution using padpaper.
A solid sample contains unknown amounts of potassium and magnesium chloride and moisture. 1.193 g of the sample is dissolved in water and the solution is diluted to 250.00 mL. 25.0 mL of the sample is allowed to pass through an H + -saturated cation exchanger, the eluate consuming 22.03 mL of a 0.100 M NaOH solution. The moisture content of the sample was determined to be 5.22%. Calculate the % by weight of potassium and magnesium chloride in the sample.
The total cation content of natural water is often determined by exchanging the cations for hydrogen ions on a strong acid ion-exchange resin. A 25.00 mL sample of a natural water was diluted to 100.00 ML with distilled water, and 2.06 g of a cation - exchange resin was added. After stirring, the mixture was filtered and the solid remaining on the filter paper was washed with three 15.00 mL portions of water. The filtrate and washings required 16.30 mL of 0.0282 M NaOH to give a bromocresol green end point. a) Calculate the number of millimoles of cation present in exactly 1.00 L of sample. b ) Report the results in terms of milligrams of CaCO3 per liter. Only typed solution.
Stock iron(II) solution (200Ug mL-1 Fe) ferrous ammonium sulfate hexahydrate mass= 0.1437g, transfer it to a 100 ml beaker. add 15 ml approx of water and 15m1 'approx of dilute sulphuric acid (2M H2SO.). then transfer FeII to 100 ml flask makeup to the mark with water. calculate the moles of ferrous ammonium sulfate hexahydrate solution in unit ug/mL.
An sample of eggshell that weighs 1.0014g and is 51μm thick is titrated with disodium EDTA. A solution of the 1.0014g sample and 30 mL of HCl is vacuum filtered after being mixed. The product of the filtration is added to a 250mL volumetric flask and is diluted by being filled to the 250 mL mark with deionized water. 10 mL of this diluted mixture is mixed with EBT indicator and titrated with 0.05 M disodium EDTA. It takes 12.3 mL of disodium EDTA to notice a change in color. What percent mass of calcium is in the eggshell?
heat stability of oil in cold water fish and warm water fish?
Consider a 1.000-L stock solution of 9.69 M Na3PO4. A 2.000-mL aliquot is taken from this stock solution and diluted to a final volume of 1.000 L. A 5.000-mL aliquot is then taken from this new solution and further diluted to make a new solution with a final volume of 750.0 mL. Calculate Na+ in the final solution.
You have been tasked with determining the wastewater solids generated by a community. To determine solids, you collect two effluent samples of 100 mL each. The first sample was placed, unfiltered, in a crucible and dried at 105 ̊C overnight. The weight of the dried sample and crucible was 5.6112 g, while the weight of the crucible was 5.6000 g. The second sample was filtered. The filter and drying dish were dried overnight at 105 ̊C after which they weighed 2.1085 g. The filter and drying dish were then placed in a muffle furnace at 550 ̊C for 30 mins, after which they weighed 2.103 g. The drying dish weighs 1.6000 g and the filter weighs 0.5 g. a) Determine the concentration of TS, TSS, VSS, FSS and TDS in mg/L: b) Does TSS concentration meet the federal effluent regulations? If not, what removal techniques would you recommend and what minimum percent must be removed prior to discharge?
Electrical Conductivity of Several Solutions Solution or Liquid Formula Conductivity (non-conductor, poor conductor, good conductor, very good conductor, excellent conductor) distilled water H2O 0.1 M sodium chloride NaCl(aq) 0.1 M ammonium nitrate NH4NO3(aq) 0.1 M calcium sulfate CaSO4(aq) ethanol C2H5OH glycerol C3H8O3 0.1 M sucrose C12H22O11(aq) glacial acetic acid CH3COOH 0.1 M acetic acid CH3COOH(aq) 0.1 M ammonia NH3(aq) 0.1 M sodium hydroxide NaOH(aq) 0.1 M hydrochloric acid HCl(aq)
using exactly 5.00 mL of 0.0400 M stock CuSO4 solution. Add 100 mL of water. Data for Part IMass of empty dish: 32.470 g empty dishVolume of 0.0400 M solution: 5.00 mL CuSO4 solution.Mass of dish and 0.0400 M solution: 37.497 g dish and solutionMass of dish and CuSO4 solid: 32.503 g dish and CuSO4 solidCalculations for Part I1. Calculate the mass of solution2. Calculate the mass of solid CuSO4 dissolved in the solution.3. Calculate the number of moles of solid CuSO4 dissolved in the solution.4. Calculate the mass of water evaporated from the solution.5. Calculate the density of solution, (g solution/mL solution).6. Calculate the % by mass, CuSO4 in solution (100 x g CuSO4/g solution).7. Calculate the molality of solution (moles CuSO4/kg solvent).8. Calculate the molarity of solution (moles CuSO4/L solution).9. Given that the true molarity is 0.0400 M, calculate the percent error of your result.
A core sample is saturated with an oil (?o = 35oAPI), gas and water. The initial weight of the sample is 224.14 g. After the gas is displaced by water (?w = 1 g/cm3 ), the weight is increased to 225.90 g. The sample is the placed in a Soxhlet distillation apparatus, and 4.4 cm3 water is extracted. After drying the core sample, the weight is now 209.75 g. The sample bulk volume, 95 cm3 is measured in a mercury pycnometer. Find the porosity, water saturation, oil saturation, gas saturation and lithology of the core sample.
A solution of sulfuric acid was made by dissolving 20.0g of 98% sulfuric acid in a 250mL of water. (H2SO4 = 98.078 g/mol; H2O = 18.015 g/mol)Additional information for 35-37 What if the solution has a total volume of 262ml? 1. Express the concentration of this solution in % by weight.a. 7.3%b. 4.4%c. 8.0%d. 7.8% 2. Express the concentration in molaritya. 0.10 Mb. 2.00 Mc. 0.76 Md. 0.93 M 3. Express the concentration in normalitya. 2.0 Nb. 1.5 Nc. 1.0 Nd. 0.76 N 4. Express the concentration in molalitya. 0.80 mb. 0.77 mc. 1.00 md. 1.50 m