M=23 kip*ft 4 kip Y-direction for roller? 5 ft 3 ft 9 kip X-direction for the pinned support (triangle)? 3 ft Y-direction for the pinned support (triangle)? 2 ft For the beam above, what are the support reaction forces? Please report your answers in the units of 'kips' and to 2 significant digits (i.e. two decimal places). 6 in 9 in

M=23 kip*ft 4 kip Y-direction for roller? 5 ft 3 ft 9 kip X-direction for the pinned support (triangle)? 3 ft Y-direction for the pinned support (triangle)? 2 ft For the beam above, what are the support reaction forces? Please report your answers in the units of 'kips' and to 2 significant digits (i.e. two decimal places). 6 in 9 in

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.5.9P: A seesaw weighing 3 lb/ft of length is occupied by two children, each weighing 90 lb (see figure)....

See similar textbooks

Similar questions

Two steel wines support a moveable overhead camera weighing W = 28 lb (see figure part a) used For close-up to viewing of field action at sporting, events. At some instant, wire I is at an angle a = 22° to the horizontal and wire 2 is at angle fi = 40°. Wires I and 2 have diameters of 30and 35 mils, respectively. (Wire diameters are often expressed in mils; one mil equals 0.001 in.) (a) Determine the tensile stresses s and s2 in the two wires. (b) If the stresses in wires 1 and 2 must be the same, what is the required diameter of wire 1 ? (c) To stabilize the camera for windy outdoor conditions, a third wire is added (see figure part b). Assume the three wires meet at a common point coordinates (0, 0. 0) above the camera at the instant shown in figure part b. Wire I is attached to a support at coordinates (75 ft, 48 ft, 70 Ft). Wire 2 is supported at (-70 ft. 55 ft, 80 Ft). Wire 3 is supported at (-10 ft. -85 Ft, 75 ft). Assume that all three wires have a diameter of 30 mils. Find the tensile stresses in all three wires
At 90 degrees of knee flexion, the mechanical stress at the tibiofemoral joint is 821.43 N/cm^2. If the compressive force is 1150 N, what is the magnitude of joint contact area (in cm^2)?
Write a short explanation for the following terms: 1. Tensile, Compressive and Shear Loads 2. Bending, Torsion and Buckling 3. Stress 4. Strain 5. Young's Modulus of Elasticity 6. Design Limit Load & Design Ultimate load 7. Safe-life 8. Fail-safe structure 9. Fatigue 10. Loads on fuselage
For a concrete column that is part of a braced frame, if the column is square, tied, 18 inches per side, 16 feet long, classify the column as slender or non slender. Assume that at one end of the column a clockwise moment of 100 k-ft is present, and that at the other end of the column a counter-clockwise moment of 25 k-ft is present. You may assume that K=1.
(a) What are the internal forces F1 and F2 in rods (1) and (2), respectively? Use the sign convention for internal axial forces. in kN (b) Determine the cross-sectional area for the rods. in mm^2 (c) If there were no temperature change, what would be the elongations δ1,P and δ2,P of rods (1) and (2), respectively, due to the load P? in mm (d) If there were no temperature change, what would be the magnitude of the horizontal deflection at end C of the compound rod due to load P? (e) Compute the change in temperature required to produce zero horizontal deflection at end C of the compound rod. Enter a positive value for a temperature increase, or a negative value for a temperature decrease. in degrees celcius
The cross sectional area of the bar is 5cm^2. Use E = 70GPa for aluminum, and E = 200 GPa for steel What is the elongation in segment AB (Aluminum)? a. 7.8571 x10^-3 m b. 6.8571 x10^-3 m c. -7.8571 x10^-3 m d. -6.8571 x10^-3 m What is the elongation in segment BC (Steel)? a. -3x10^-3 m b. 3x10^-3 m c. 2 x10^-3 m d. -2 x10^-3 m What is the elongation in segment CD (Aluminum)? a. -6.8571 x10^-3 m b. 6.8571 x10^-3 m c. -2.8571 x10^-3 m d. 2.8571 x10^-3 m What is the total elongation of the bar? a. 5 x10^-3 m b. 6 x10^-3 m c. 4 x10^-3 m d. -6 x10^-3 m -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.- Direction of the assumption of the equilibrium equation must be shown, no direction will be marked wrong.
Write a short explanation for the following terms: 1. Strain 2. Young's Modulus of Elasticity 3. Design Limit Load & Design Ultimate load 4. Safe-life 5. Fail-safe structure 6. Fatigue 7. Loads on fuselage
1. How would you predict if a column will fail in buckling or in compression? Draw a graphshowing the relationship between critical stress, yield stress, and radius of gyration.
A square post which is made up of two parts is glued atplane ABCD with the angle α = 30° with the vertical.Allowable compressive stress @ glue = 5.2 MPaAllowable shearing stress = 3.5 MPaP = 36 kN. 1. What is the minimum post dimension, w (mm), withoutexceeding the allowable shearing stress at the glue? 2. What is the minimum post dimension, w (mm), withoutexceeding the allowable compressive stress at the glue? 3. What angle, α, will give the maximum shearing stress? with brief explanation each part
The bottom of a steel "boat" is a 5.00 mm ×× 9.00 mm ×× 2.00 cmcm piece of steel (ρsteel=7900kg/m3)(ρsteel=7900kg/m3). The sides are made of 0.550 cmcm -thick steel. To do this problem, assume that the bottom of the boat is the full dimensions, but that the sides of the boat are welded onto the top of the bottom (so the total side height is the height of the side plus the thickness of the bottom). h= ? cm
Describe the Torsional Moment?
Floor joists are structural members which support flooring in structures, as in the diagram on the right. The floor sits upon the minor length of the joist, and the joists are set at equal spacing to reach the desired floor stiffness. How many 2x6 joists would it take to equal the floor stiffness of the same floor supported by ten (10) 2x12 joists of the same species?