Step 3 Determine the rate of heat transfer to the steam flowing through the reheater, in kW Question 19 Steam enters the first-stage turbine shown in the figure at 40 bar and 500°C with a mass flow rate of 110000 kg/hr. Steam exits the first-stage turbine at 20 bar and 400°C. The steam is then reheated at constant pressure to 500°C before entering the second-stage turbine. Steam leaves the second stage as saturated vapor at 0.6 bar. Assume steady state operation and ignore stray heat transfer and kinetic and potential energy effects. Steam + P₁ = 40 bar T₁, mi Wcv Turbine = P₂ = 20 bar T₂=400°C Reheater Turbine P3 = 20 bar T3 = 500°C 4 + Qreheater Determine the volumetric flow rate of the steam at the inlet to the first-stage turbine, in m³/min, the rate of heat transfer to the steam flowing through the reheater, in kW, and the total power produced by the two stages of the turbine, in kW. Step 1 Determine the volumetric flow rate of the steam at the inlet to the first-stage turbine, in m³/min. (AV) 1 m³/min Step 2 Determine the total power produced by the two stages of the turbine, in kW. kW Saturated vapor, P4 = 0.6 bar Power

Step 3 Determine the rate of heat transfer to the steam flowing through the reheater, in kW Question 19 Steam enters the first-stage turbine shown in the figure at 40 bar and 500°C with a mass flow rate of 110000 kg/hr. Steam exits the first-stage turbine at 20 bar and 400°C. The steam is then reheated at constant pressure to 500°C before entering the second-stage turbine. Steam leaves the second stage as saturated vapor at 0.6 bar. Assume steady state operation and ignore stray heat transfer and kinetic and potential energy effects. Steam + P₁ = 40 bar T₁, mi Wcv Turbine = P₂ = 20 bar T₂=400°C Reheater Turbine P3 = 20 bar T3 = 500°C 4 + Qreheater Determine the volumetric flow rate of the steam at the inlet to the first-stage turbine, in m³/min, the rate of heat transfer to the steam flowing through the reheater, in kW, and the total power produced by the two stages of the turbine, in kW. Step 1 Determine the volumetric flow rate of the steam at the inlet to the first-stage turbine, in m³/min. (AV) 1 m³/min Step 2 Determine the total power produced by the two stages of the turbine, in kW. kW Saturated vapor, P4 = 0.6 bar Power

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A Steam turbine operates under steady flow conditions receiving steam at the following state: Pressure 15 bar, internal energy 2700kj/kg; specific volume 0.17m3/kg and velocity 100m/sec. The exhaust steam from the turbine is at 0.1 bar with internal energy 2175kj/kg. specific volume 15m³/kg and velocity 300m/sec. The intake is 3m above the exhaust. The turbine develops 35KW and the heat lost over the surface of the turbine is 20kj/kg. Determine the steam flow rate through the turbine
Air enters the turbine of a gas turbine at 1200 kPa, 1200 K, and expands to 100 kPa in two stages. Between the stages, the air is reheated at a constant pressure of 350 kPa to 1200 K. Both turbines have same isentropic efficiency 85% Determine, in kJ per kg of air flowing (a) the work developed by each stage. (b) the heat transfer for the reheat process. (c) the increase in net work as compared to a single stage of expansion with no reheat
Figure 1 shows a regenerative gas turbine power plant. Air enters the compressor with a mass flow rate of 1 bar, 27°C and 0.562 kg/s and is compressed to 4 bar. The isentropic efficiency of the compressor is 80% and the regenerator efficiency is 90%. All the power generated from the high pressure turbine is used to run the compressor. The low pressure turbine provides net power output. The isentropic efficiency of each turbine is 87% and the temperature at the inlet of the high pressure turbine is 1200 K. a) Net power output (kW) ? b) thermal efficiency ? c) Calculate the temperature (K) of the air at states 2, 3, 5, 6 and 7. find it
5. The cooled water from a cooling tower returns to the condenser at 21°C at a mass flow rate of 54.4 kg/s. The air entering at state 1 has h₁ = 47.7 kJ/kg da and w₁ = 0.006 kg v/kg da. The air leaving the cooling tower at state 2 has h₂ = 116.5 kJ/kg da and w₂ = 0.027 kg v/kg da. The makeup water is supplied at 25°C and the mass flow rate of dry air is 54.4 kg da/s. What is the temperature of the warm water entering the tower? Express your answer in °C.
Steam enters a turbine stage with pressure of 5 bar, specific volume of 0.125m³ /kgm and an enthalpy of 3620 kJ/kgm at 75 m/s and leaves the same stage with pressure of 1200 mm Hg, specific volume of .0345 m³ /kgm and an enthalpy of 2800 kJ/kgm at 128 m/s. Calculate the work done by the steam.
Refrigerant 22 enters a compressor operating at steady state and is compressed adiabatically to a higher pressure. Would you expect the power input to the compressor to be greater in an internally reversible compression or an actual compression?
THERMODYNAMICS A 1.5-kW power output is produced by a small, high-speed turbine that runs on compressed air. The entrance state is 400 kPa and 52 degrees celcius, whereas the exit state is 150 kPa and -43 degrees celcius. Determine the needed mass flow rate of air through the turbine assuming low velocities and an adiabatic process.
Apply SFEE for the steam nozzle used in the steam powerplant and determine the outlet velocity of the steam using thefollowing details.Steam at 18 bar and 350°C steadily enters a nozzle whose inletarea is 200 cm2. The mass flow rate of the steam is 4.5 g/s. Heatlosses from the nozzle per unit mass of the steam are estimatedto be 2.8 kJ/kg. Steam leaves the nozzle at 14 bar, 300 °C.Determine the outlet velocity of the steam.
.......A gas turbine power plant is operated between 1.5 bar and 15 bar with minimum and maximum cycle temperatures of 25 C and 1420 C, respectively. Neglect the mass of the fuel. Determine the following: Work of the compressor in kJ/kg (2 decimal places) = Work of the gas turbine in kJ/kg (2 decimal places) = Heat added in the combustion chamber in kJ/kg (2 decimal places) = Net Work in kJ/kg (2 decimal places) = Thermal Efficiency in % (1 decimal place only) =
A flash chamber has R-134A entering with a quality of 0.25 at a pressure of 5 bar. The saturated liquid from the flash chamber goes through a throttling value, an evaporator, and a compressor where it is compressed to 5 bar and 40°C. The saturated vapor from the flash chamber recombines with the remaining refrigerant in an open heat exchanger at a pressure of 5 bar. What are the enthalpy and temperature of the refrigerant exiting the heat exchanger?
A four-cylinder, four-stroke, 1.6-L gasoline engine operates on the Otto cycle with a compression ratio of 11. The air is at 100 kPa and 37°C at the beginning of the compression process, and the maximum pressure in the cycle is 8 MPa. The compression and expansion processes may be modeled as polytropic with a polytropic constant of 1.3. Using constant specific heats at 850 K, determine the specific fuel consumption, in g/kWh, defined as the ratio of the mass of the fuel consumed to the net work produced. The air– fuel ratio, defined as the amount of air divided by the amount of fuel intake, is 16.
Water vapor enters a turbine at p1 = 5 bar, T1 = 500oC and exits at p2 = 1 bar. The work developed is measured as 351 kJ per kg of water vapor flowing. Determine the isentropic turbine efficiency.