must transmit the torque of 34 kN-m. The total angle of twist must not exceed 3°. The maximum shearing stress must not exceed 110 MPa. Use G = 83 GPa. Which of the following gives the minimum required polar moment of inertia? Which of the following gives the minimum outside diameter so that the allowable shearing stress will not be exceeded?

Q: If a drive shaft with a shear modulus 120GN/m² and a length of 0.45m is to be subjected to a torque.…

A:

Q: Calculate the maximum permissible torque on a hollow shaft if the maximum allowable shearing stress…

A:

Q: A hollow steel (G = 12,000 ksi) shaft has diameters of 6 in. and 4 in. and an allowable shearing…

A: Given data, Modulus of rigidity of the steel shaft, G = 12000 ksi G = 12×106 psi Outer diameter of…

Q: A hollow circular torsion member has an outside diameter of 22 mm and inside diameter of 18 mm, with…

A: GivenDo=22mmDi=18mmD=20mmτ=70MPa at mean diameterG=77.5GPa

Q: A hollow bronze shaft of 75 mm outer diameter and 50 mm inner diameter is slipped over a solid steel…

A: Draw a diagram for the problem. Write the given data in the problem. T=4 kN·mD=75 mmd=50 mm Here, T…

Q: Hollow and solid shafts have the same material, length and the same outer radius as shown. The inner…

A:

Q: 1) A stepped steel shaft consists of a hollow shaft 2.5 m long with an outside diameter of 110 mm…

A:

Q: A hollow cylindrical steel shaft is 1.5 m long and has inner and outer diameters respectively equal…

A: Given data as per question L=1.5 mDi=40 mmDo=60 mmAllowable shear stress =120 Mpa

Q: A solid circular shaft is required to transmit 200 kW while turning at 90 rpm (rev/min). The…

A: Consider a shaft having diameter 'D' is subjected to a twisting moment 'T'. Then, from torsion…

Q: A flanged bolt coupling is used to connect a solid shaft 94 mm in diameter to a hollow shaft 100 mm…

A:

Q: A hollow shaft's inner diameter is half of its outer diameter D. Show that the maximum torque that…

A:

Q: A solid titanium alloy [G=114⁢ GPa] shaft that is 950 mm long will be subjected to a pure torque of…

A: Given that G=114Gpa=114×103Mpa L=950mm T=195 N-m τall=145Mpa θall=30 min diameter  on the basis of…

Q: An aluminum shaft with a constant diameter of 70 mm is loaded by torques applied to gears attached…

A:

Q: A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is…

A:

Q: What is the minimum diameter of a solid steel shaft that will not twist through more than 3.18…

A:

Q: What is the correct formula for the maximum shearing stress in case of shaft with diameter d and…

A:

Q: An aluminum rod AB of diameter 2.8 inches is connected to a lever of length L = 5.6 feet. Consider…

A: Given:diameter, d=2.8 inL=5.6 ftheight, H=3.4 ftTorsional shearing stress of aluminium, ζa=1111 psi

Q: Need in 1 hour please, thank u! If a twisting moment of 10,000 lb-in is impressed upon a 1 and 3/4…

A:

Q: A solid shaft in a rolling mill transmits 30 hp at 100 rpm. Find the diameter in mm of the shaft so…

A:

Q: circular solid shaft made of vibranium has G=80 Mpa and has a limiting torsional shear stress of 60…

A:

Q: 3 m solid shaft twist 2° when a 10 kN-m torque is applied. If the shaft has shear modulus of…

A:

Q: Q7: A hollow steel shaft (3 m) long must transmit a torque of (25 kN.m). The total angle of twist in…

A: The greatest stress (tensile, compressive, or bending) that may be applied to a structural material…

Q: Determine the minimum diameter that can be used for a solid circular steel shaft  which is  limited…

A:

Q: aft with a hollow cross section is subjected to torque of magnitude T = 5.5 kN-m. If the outer…

A: Given:T=5.5 kN.mdo=0.1 mt=10 mm

Q: A solid shaft 125 mm in diameter transmits 120 KW at 160 rpm. Taking C = 8 x 10 N/mm² and length of…

A: Given data as per question shaft dimeter =125 mmPower transmitted =120 kwSpeed=160 rpmC = 8×10…

Q: 1) What is the minimum diameter of a solid steel shaft that will not twist through more han 3º in a…

A: Given that ,  Length l=6 m Torqueτ=14kNmG=83GPaTwist angle θ=3°

Q: If a twisting moment of 10,000 lb-in is impressed upon a 1 and 3/4 inch diameter shaft, what is the…

A:

Q: Calculate the maximum and minimum shear stress in a hollow circular shaft of outer diameter 20 mm…

A: Given data T=92.7 N-mD=20 mmt=2 mmd=16 mm

Q: torque, T, should be applied to the end of the steel sha. duce a twist of 1.5°? Use G = 80 GPa for…

A: Given Data→ Steel shaft Angle of twist θ=1.5° Convert from degree to radian θ=0.0261799 G=80 GPa…

Q: 4. A hollow shaft with outside diameter of 98mm if it is subjected to a maximum torque of 5758N-m.…

A:

Q: A machine shaft is supported on bearings 1.2 m apart is to transmit 150 kW at 300 rpm while…

A: Given      Power, P = 150 kW     Speed, N = 300 rpm Shear stress = 50 MPa Find   Shaft diameter, d

Q: A solid circular shaft of diameter 220 mm is to be replaced by a hollow shaft in which the ratio of…

A:

Q: What is the minimum diameter of a solid steel shaft where the allowable angle of twist cannot…

A:

Q: (Problem 3.67 from the text book) Determine the maximum shearing stress in a solid shaft of 18-mm…

A: Given data: d=18 mmP=3.4 kW Need to determine the shear stress in the shaft.

Q: Fig. P3.1 18 mm 3.1 Determine the torque T that causes a maximum shearing stress of 70 MPa in the…

A:

Q: A hollow steel [G = 12,000 ksi] shaft with an outside diameter of 3.50 in. will be subjected to a…

A:

Q: steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is…

A: → Given Data :       T = 1200 N.m       z = 40 mPa      Q = 0.75  / m      G = 78 GPaa) For Solid…

Q: A solid steel shaft will not twist through more than 3° in a 6.0 m length when subjected to a torque…

A: Givenθ=3oL=6mT=12kNmG=83GPa

Q: In a certain machine, a shaft 3 inches in diameter caries a bending moment of 2210 Ib-ft. What…

A:

Q: Determine the diameter of a solid steel shaft which will transmit 112.5 kW at 200 rpm. Also…

A: Given data,  P= 112.5 kW =112500 W  N= 200 rpm.  θ=1.5° =0.0261799 rad.  τ=55 N/mm² =55000000 N/m²…

Q: A solid 1.500-in.-diameter steel [G = 11,000 ksi] shaft is subjected to torques TB = 190 lb-ft and…

A: Given Datad=1.5inG=11,000ksiTB=190 lb-ftTD=140 lb-fta=42 inb=72 inc=36 in

Q: An aluminum shaft with a constant diameter of 70 mm is loaded by torques applied to gears attached…

A:

Q: a) A solid alloy shaft 5cm diameter is to be coupled in series with a hollow steel shaft of the same…

A:

Q: The transmitted torque of a hollow shaft is 3400 N-m at a shearing stress of 55 MPa. If the outside…

A:

Q: A hollow cylindrical steel shaft is 1.5 m long and has inner and outer diam-eters respectively equal…

A: Given: do=60 mm=0.06 mdi=40 mm=0.04 mτmax=120 MPa To determine: Maximum torque can be applied for…

Q: 2) Determine the maximum torque that can be applied to a hollow circular steel shaft of 100mm…

A:

Q: A motor drives 50 hp to a shafting 1 1/2 in. diameter and 3 ft. long. If the maximum shearing stress…

A:

Q: A propeller shaft in a ship is 325 mm in diameter and 4.875 m in length. The allowable shearing…

A: Given: The diameter of the shaft is D=325 mm. The length of the shaft is L=4.875 m. The allowable…

Q: A hollow steel shaft of 95 mm external diameter and 65 mm internal diameter is subjected to a…

A: