need to prepare a standard calibration curve for gamma globulin. absorbances on Y and mg of standard protein per assay on X. used 0.1mg/ml gamma stock for tubes 2-6. (Water (ml), gamma (ml), Abosrbance)--> (.036, .004, .290) (.036, .008, .358) (.024, .016, .341) (.016, .024, .520) (.008, .032, .597) - What is the math and how do you get the standard curve?

need to prepare a standard calibration curve for gamma globulin. absorbances on Y and mg of standard protein per assay on X. used 0.1mg/ml gamma stock for tubes 2-6. (Water (ml), gamma (ml), Abosrbance)--> (.036, .004, .290) (.036, .008, .358) (.024, .016, .341) (.016, .024, .520) (.008, .032, .597) - What is the math and how do you get the standard curve?

Curren'S Math For Meds: Dosages & Sol

11th Edition

ISBN:9781305143531

Author:CURREN

Publisher:CURREN

Chapter13: Dimensional Analysis/units Conversion

Section: Chapter Questions

Problem 1.8P

See similar textbooks

Similar questions

Total protein: Do you think that refractive index could be used as a regular method for serum protein determinations? If yes, what limitations does it have. If not, why not? What are the major interferences in the biuret method? Refractometry method?
In the experiment performed for the determination of cholesterol, the function of the calibration curve obtained using 25-400mg/dL standard cholesterol solutions was determined as y= 0.0009x. If the absorbance of the serum sample is determined as 0.28, what is the amount of cholesterol in the sample, in mg/L?
You will be given 1 mL of a 2.0 mg/mL solution of bovine serum albumin (BSA) and 1 mL of a 2.0 mg/mL solution of bovine gamma globulin (BGG). From these solutions, you will need to make 100 μL of each of the following standards using 1x MBP purification buffer as the diluent for preparation of a standard curve: 1000 μg/mL, 750 μg/mL, 500 μg/mL, 250 μg/mL, 125 μg/mL, and 0 μg/mL.
4 mL of 10% TCA solution was added to 1 mL of serum and after mixing, it was waited for two minutes and filtered through non-phosphorus filter paper. 1 mL of the filtrate was taken and 13 mL of distilled water, 4 mL of sulfomolybdic acid and 2 mL of dilute SnCl2 solution were added and mixed, and after waiting for 15 minutes, the absorbances of the obtained solutions against pure water at 520 nm were read. If the function of the calibration graph obtained with 0.5-2.5 mg/mL standard phosphorus solutions is y= 0.245x + 0.107 and the absorbance value of the serum sample is 0.109, what is the amount of phosphorus in the sample?
Given that the normal range for serum protein is about 7 g/100ml and albumin is about 4 g/100ml, what clinical conclusions can you draw from the following samples A-C? If samples are not normal, what protein fraction is increased/decreased and with what disease is this protein pattern likely to be associated? Sample A: total protein = 14 g/100mlalbumin= 8 g/100 ml Sample B:total protein = 5.8 g/100ml albumin = 4 g/100 ml Sample C:total protein = 3.5 g/100mlalbumin = 2g/100 ml
The order is to give 45 mEq. The dosage available is 30 mEq in 15 mL. How many mL do you give?
How much serum is needed to create 2μL of a 1:20 dilution?
In the experiment performed for the determination of cholesterol, the function of the calibration curve obtained using 25-400mg/dL standard cholesterol solutions was determined as y= 0.0009x. If the amount of cholesterol in the serum sample is determined as 3.11 g/L, what is the absorbance value of the sample? A. 0,280 B. 0.028 C. 0.208 D. 0.82
KCI for injection contains 40 mEq in 20 mL. An order requires 15 mEq, how many mL are needed?
1. In the preparation of the standard curve for protein analysis, 50 mnBSA (bovine serum albumin) dissolved in H2O to a final volume of 5mL was used as stock solution. What is the weight of BSA in 0.1 mL ofstock solution? In 0.2 mL? 2. The above mentioned aliquots (#9) which were diluted with enoughwater to a final volume of 1 mL were assayed colorimetrically andyielded the following absorbance readings:mL stock mL H2O Absorbance0.2 0.8 0.1000.4 0.6 0.2000.6 0.4 0.3000.8 0.2 0.4001.0 0.0 0.500 i. Tabulate mg BSA vs. absorbance readingii. Draw the curve where mg BSA is on x-axis and absorbance ony-axis (use graphing paper).iii. Calculate the slope of the curveiv. If a sample solution has an absorbance of 0.332, determinemg protein of the sample.
You perform a Bradford assay to determine the concentration of isolated α-lactalbumin. You use 50 μL of a two-fold diluted solution of α-lactalbumin in the assay. You generate a standard curve with the following equation for the line: y = 0.163x + 0.082. The absorbance of your sample was 0.674 AU. What is the concentration of α-lactalbumin, in mg/mL, in your sample? Give your answer to three significant figures.
If a pharmacist added each of the following to 22-g packages of 2% mupirocin ointment, what would be the percentage strengths of the resulting ointments: (a) 0.25 g mupirocin powder and (b) 0.25 g of nonmedicated ointment base? (answer to two decimal places). answers: (a) 3.10% w/w (b) 1.98% w/w