novel heat engine is being considered for producing work from the thermal energy  contained in the wastewater discharge from a large food-processing plant. On an average  day, 35 ° C wastewater leaves the plant and is discharged into the ocean at 1,000 gallons  per minute. If the average annual ocean temperature is 10 ° C at that location, what is the  maximum power that could be produced by this heat engine? What would be the thermal  cycle efficiency of your maximum power engine? You can assume that the heat capacity

Q: 10.3 (a) Why is it desirable to employ high inlet gas temperatures in gas turbine plants for land…

A: INTRODUCTION: Land-based gas turbines are classified into two types: one is heavy frame engines and…

Q: (COP) of the heat pump is

A: Given data; Temperatures T1>T3>T2Heat pump receives the entire work output (W) of the heat…

Q: A continuous and aligned fiber-reinforced composite is to be produced consisting of 30% vol aramid…

A: Write the give data. Ef=121.68 GPaVf=0.30Em=3.42 GPaVm=0.70

Q: A high-impulse universal testing machine is being used to determine the Young's Modulus of a…

A: Given data Load applied = 35000 N length of specimen = 20 cm = 0.2 m Thickness of specimen = 1.5 cm…

Q: Fill in the blanks in the following: 1. If ā= (3,-2, 6) and b = (4, −1, −6) the axb = ………………….…

A: Vectors are given, Find,

Q: Calculate the (total tensile strength) of the mitotic tensile strength test for the information in…

A:

Q: Determine the magnitude of the vertical deflection of

A: Given data;  Applied moment ,M=2 m Length,l=4 m EI=300 N.m2 Determine magnitude of vertical…

Q: This side of the dam always has the higher water level O dam height O Downstream O Upstream O Top…

A:

Q: □ 18 F.V.

A: According to the details provided in the question, we need to draw three projection views.

Q: Two identical cylinders methods cant be used to measure The hand writt Select one: True O False 4

A: Yes, it's true.

Q: Determine smaller diameter, All dimensions are in mm) 110.916 091 100.916 80.916 mm cant be…

A: The smaller diameter is 80.916 mm.

Q: The layer at the center of gravity of the beam as shown in the below figure, will be M M O In…

A: Pure Bending or simple Bending is that in which bending moment is constant along the length i.e.,…

Q: In analyzing real processes, when is the entropy balance helpful as opposed to merely being an…

A: We can assume a process from A to B, where the substances flowing in it from A to B. And if the…

Q: Q6. A small size cooling tower is designed to cool 400kg of water per minute. The water enters the…

A: Given DataTw1=43.5°CTa1=18.5°Cϕ=60% RHTa2=27°Cϕ=100%h2=85.01kJ/kgmw=400kg/minma=600m3/minw=4kW

Q: the reading of this tool is

A:

Q: Find the value of stress Force 2.2 N Area=2 m2

A: Given data : Area=A Force=F   Required : Stress

Q: (1) why the flow faster at the pipe center when you observe few millimeters from the pipe inlet; (2)…

A: INTRODUCTION: Whether the flow is laminar or turbulent determines the form of the velocity profile…

Q: A hollow steel shaft with an outside diameter of 90 mm and a wall thickness of 10 mm is subjected to…

A:

Q: Q2(30 %) Determine the resultant of forces system shown in Figure and locate it with respect to…

A:

Q: Consider a cylindrical specimen of a steel alloy with 8.5 mm diameter and 80 mm long that is pulled…

A: Calculate Modulus of Elasticity in MPa and psi Modulus of Resilience in MPa and psi

Q: A block having a weight of 8 lb is suspended from a spring having a stiffness k = 40 Ib/ft. If the…

A:

Q: Find the value of stress Force 2.2 N Area=2 m2

A: Given data : Area is denoted by A Force is denoted by  F   Required : Stress

Q: Q5) The motor-pump system shown in Fig. 3 is modeled as a rigid bar of mass m = 50 kg, and mass…

A: Given m = 50 kg I = 100 kg m2 k1 = 500 N/m k2 = 200 N/m To find System natural frequencies

Q: Calculate the work done when 1 lb mol of water evaporates completely at 212°F in the following…

A: Introduction: Flow work denotes the flow of energy and mass over the system's boundary. Non-flow…

Q: 1) A 6061-T6 aluminium alloy flat, simply supported disk valve of 0.2 m diameter and 10 mm thickness…

A: following is the solution to the above problem-

Q: Steam enters the high-pressure turbine at 15,000 kPa and 873 K in a 15,000-kW steam power plant that…

A: Given data Conditions at high Pressure conditions : 15000 kPa and 873 K Low Pressure conditions : 4…

Q: natural frequencies -

A: m=50 kg                                   Jo=100 kg-m2k1=500N/m…

Q: Explain the answer and include an illustration. Why do distorted amorphous polymers have more…

A: INTRODUCTION: Polymers are distinct from other forms of materials due to their large molecular…

Q: Which of the following has no unit O strain

A: Ans: Strain

Q: * The energy absorbed in a body, when it is strained within the elastic limits, is known as O Strain…

A: The correct answer is STRAIN ENERGY  STRAIN ENERGY: The energy absorbed or stored in a body when it…

Q: Describe what is coining and embossing metal. What is the differences between the two processces?…

A: Coining-  1. Operation in which raised surfaces are created in metal.  2. During operation there is…

Q: 6. A small size cooling tower is designed to cool 400kg of water per minute. The water enters the…

A:

Q: Superheated steam at 652 psia and 608 F is generated in an Oil-fired boiler at the rate of 100,000…

A: Write the enthalpy of the superheated steam. hg=1290.72 Btu/lb Write the enthalpy of the feed water.…

Q: Using Combination set, The angle shown by the arc can be measured

A: Given 3D shape To find Verify whether combination set can be used for angle measuring

Q: Find the value of stress Force 2.2 N Area=2 m2

A:

Q: An orifice meter with 150 mm diameter is inserted in a pipe of 300 mm the pressure difference…

A: When a 150 mm orifice metre is placed into a 300 mm pipe, the pressure difference recorded by a…

Q: 4-A rigid tank is divided into two compartments by a partition. One compartment contains 3 kmol of…

A:

Q: Calculate the capillary effect in mm in a glass tube of 4mm diameter, when immersed in (1)water,…

A:

Q: Q6) A refrigerator with R-12 as the working fluid has a minimum temperature of -10°C and a maximum…

A:

Q: Problem 12-9 A curved cantilever AB in the form of quadrant of a circle carries a load W at the free…

A: As illustrated in the diagram, a curved cantilever AB in the shape of a quadrant of a circle…

Q: A through hole is drilled in an aluminum alloy plate of 15 mm thickness with a drill bit of diameter…

A:

Q: An open storage vessel has 3 m of oil SG = 0.82 and 6 m of water. The pressure at the bottom is:

A:

Q: 2. A simple-ideal Brayton cycle using air as the working fluid has a pressure ratio of 8. The…

A: Given: The pressure ratio, r = 8 The minimum temperature, T1 = 300 K The maximum temperature, T3 =…

Q: Using Combination set, The angle shown by the arc can be measured. hand written plzzz Select one: O…

A: Using combination set , the angle of arc shown can be measured or not ?

Q: A refrigerator used to cool a computer requires 1.2 kW of electrical power and has a COP of 1.8.…

A: Electrical power input = Power required to run compressor = Work input = 1.2 kW COP of the…

Q: The impeller of the centrifugal pump is 350 mm diameter, and the width of the blade passages at…

A: Diameter of the impeller (d) = 350 mm = 0.35 m width of the balde passage (w2) = 18 mm = 0.018 m…

Q: H.W1 The beam is subjected to the linearly varying distributed load. Determine the maximum…

A: Given   Length = L   Load, P = w0 Find   Deflection

Q: A boiler installed where the atmospheric pressure is 755 mm Hg. Has a pressure 12 kg/cm2. What is…

A:

Q: H G F E 10%, 13' 16' -26'- D 2000 lb C B 2000 lb T 10' 10' 10' MAY

A:

Q: Entry of liquid into the pump is axial and exit from the pump

A: Given data;  Blade outer radius,r= 25 mm Power,P=2 KW=2000W N=2000 rpmEntry of liquid into the pump…