O Gen Chem Unit la - Measureme x O https://www.bookwidgets.com/play/NGejLxXT-iQAEfd3mfAAAA/ZCNV3Z/gen-chem-unit-17teacher id%=6079380641021952 Gen Chem Unit la - Measurement & Uncertainty 141- / 1 QUESTION 33 In lab you measure out the volume of a liquid 4 times. The measurements you got were 16.4 mL, 16.6 mL, 16.5 mL, and 16.4 mL. What is the average, rounded to the correct number of significant figures and expressed w/ the correct units?

O Gen Chem Unit la - Measureme x O https://www.bookwidgets.com/play/NGejLxXT-iQAEfd3mfAAAA/ZCNV3Z/gen-chem-unit-17teacher id%=6079380641021952 Gen Chem Unit la - Measurement & Uncertainty 141- / 1 QUESTION 33 In lab you measure out the volume of a liquid 4 times. The measurements you got were 16.4 mL, 16.6 mL, 16.5 mL, and 16.4 mL. What is the average, rounded to the correct number of significant figures and expressed w/ the correct units?

Chemistry: Principles and Practice

3rd Edition

ISBN:9780534420123

Author:Daniel L. Reger, Scott R. Goode, David W. Ball, Edward Mercer

Publisher:Daniel L. Reger, Scott R. Goode, David W. Ball, Edward Mercer

Chapter1: Introduction To Chemistry

Section: Chapter Questions

Problem 1.20QE: If you repeat the same measurement many times, will you always obtain exactly the same result? Why...

See similar textbooks

Similar questions

Is it faster to 1) adjust the liquid level to exactly hit a graduated cylinder measurement mark or, 2) to estimate the last digit of precision in reading the volume?
1. (2×103g +7.613g)/(0.069cm3 - 0.033cm3) Carryout that operation as if it was the calculation of experimental result, and Express the answer in the correct unit and the correct number of significant figures.
2): The denisty of toluene is 0.855 g/ml. what volume og toluene would have a mass of 15.00g. show the detailed calculation and appropiate set-up wherein the density value is used as a conversion factor?
If Student A measures the volume of a liquid and reports its volume as 23.50 mLand Student B measures a different amount of the same liquid and reports itsvolume as 15.0 mL, is it likely that the students used the same measuring device?Yes or no? Explain your answer
The number 0.00754605000 whenconverted to standard exponential (or scientific) notation becomes ____ a. 7.55 x 103 b. 7.54605 x 10-3 c. 7.54605000 x 10-3 d. 7.54605000 x 103
(a) To identify a liquid substance, a student determined itsdensity. Using a graduated cylinder, she measured out a 45-mLsample of the substance. She then measured the mass of thesample, finding that it weighed 38.5 g. She knew that the substancehad to be either isopropyl alcohol (density 0.785 g/mL)or toluene (density 0.866 g/mL). What are the calculated densityand the probable identity of the substance? (b) An experimentrequires 45.0 g of ethylene glycol, a liquid whose densityis 1.114 g/mL. Rather than weigh the sample on a balance, achemist chooses to dispense the liquid using a graduated cylinder.What volume of the liquid should he use? (c) Is a graduatedcylinder such as that shown in Figure 1.21 likely to afford theaccuracy of measurement needed? (d) A cubic piece of metalmeasures 5.00 cm on each edge. If the metal is nickel, whosedensity is 8.90 g/cm3, what is the mass of the cube?
A volume of 450 mL syrup (sg = 1.31) is mixed with 350 g of water. How many mL of syrup should be added to this mixture in order to change the specific gravity (sg) to 1.21.
What is the correct scientific notation for 0.00541cm? Use "E" to indicate the base (x10). Do not include any spaces in your answer. example format: 6.02E23
Q1. Which student collected the most accurate data? Q2.Who collected the most precise data?
Using Two or More Conversion FactorsIt is often necessary to use several conversion factors in solving a problem. As an example,let’s convert the length of an 8.00-m rod to inches. The table on the back inside coverdoes not give the relationship between meters and inches. It does, however, give the relationshipbetween centimeters and inches 11 in. = 2.54 cm2. From our knowledge of SIprefixes, we know that 1 cm = 10-2 m. Thus, we can convert step by step, first from metersto centimeters and then from centimeters to inches:
how do i know which series of conversion factor SI units to use when setting up dimensional analysis. I got the answer 16.5 x 10^9 :/ and im not sure why..
Calculate the density of a spherical metal, in g/cm3, with a diameter of 4.77 in and and a mass of 2.41 lbs. 1lb=454g *1 in=2.54cm Vol of sphere= 4/3 ??3