The fluid condition at the inlet and exit of a horizontal convergent nozzle is analysed. The nozzle is operating steadily and heat loss is assumed negligible. If the specific enthalpy of fluid and velocity of fluid at the inlet are 3,314 kJ/kg and 226 km/hr respectively. At the exit the specific enthalpy of fluid is 2,563 J/kg. Calculate the exit area (in mm2Jof the nozzle when the specific volume at the nozzle exit is 0 61 m3/kg at the inlet area of 0.23 m2 and the specific volume at the inlet is 0.3 m3/kg.

The fluid condition at the inlet and exit of a horizontal convergent nozzle is analysed. The nozzle is operating steadily and heat loss is assumed negligible. If the specific enthalpy of fluid and velocity of fluid at the inlet are 3,314 kJ/kg and 226 km/hr respectively. At the exit the specific enthalpy of fluid is 2,563 J/kg. Calculate the exit area (in mm2Jof the nozzle when the specific volume at the nozzle exit is 0 61 m3/kg at the inlet area of 0.23 m2 and the specific volume at the inlet is 0.3 m3/kg.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The liquid storage tank shown in Fig has two inlet streams with mass flow rates w1 and w2 and an exit stream withflow rate w3. The cylindrical tank is 2.5 m tall and 2 m in diam-eter. The liquid has a density of 800 kg/m. Normal operating procedure is to fill the tank until the liquid level reaches a nom-inal value of 1.75 m using constant flow rates:w1=120 kg/min, w2=100 kg/min, and w3=200 kg/min. At that point, inlet low rate w1 is adjusted so that the level remains constant.However, on this particular day, corrosion of the tank has opened up a hole in the wall at a height of 1 m, producing a leak whose volumetric flow rate q4(m3/min) can be approximated by q4=0.025√h−1 where h is height in meters.(a)If the tank was initially empty, how long did it take for theliquid level to reach the corrosion point?(b)If mass flow rates w1,w2,and w3 are kept constant indefi-nitely, will the tank eventually overflow? Justify your answer.
Consider a convergent duct with an inlet area of 3 ft2 and an exit area of 2.57 ft2. Air enters this duct with a velocity of 700 ft/s and a density of 0.002 slug/ft3, and air leaves with an exit velocity of 1,070 ft/s. Calculate the density (in kg/m3) of the air at exit.
A hydroelectric power plant uses Pelton-type turbines, in which multiple nozzles are used to accelerate the waterwhich is directed onto the turbine blades, which are exposed to an atmospheric pressure of 101.325 kPa. The water enters the nozzles with an absolute pressure of 500 kPa and a speed of 5 m/s, and the nozzle outlets are exposed to atmospheric pressure and have an internal diameter of 5 cm. Consider that the specific mass of water is 1,000 kg/m3. Determine the mass flow rate of water through each of the nozzles, and explain why the actual mass flow rate will be lower.
Air enters a fan through a duct at a velocity of 6.5 m/s and an inlet staticpressure of 2.5 cm H2O less than atmospheric pressure. The air leaves the fan through aduct at a velocity of 11.5 m/s and a discharge static pressure of 7.62 cm H2O above theatmospheric pressure. If the specific weight of air is 1.20 kg/m3 and the fan delivers 9.45m3/s, determine the fan theoretical power and the fan efficiency when the power input tothe fan is 13.75 kW at the coupling?
Air flows through a long duct of constant area at 0.15 kg/s. A short section of the duct is cooled by liquid nitrogen that surrounds the duct. The rate of heat loss in this section is 15.0 kJ/s from the air. The absolute pressure, temperature, and velocity entering the cooled section are 188 kPa, 440 K, and 210 m/s, respectively. At the outlet, the absolute pressure and temperature are 213 kPa and 351 K. Compute the duct cross-sectional area and the changes in enthalpy, internal energy, and entropy for this flow. Take C=1 KJ/KgK, C,-0.717 KJ/Kg.K
Consider a turbojet-powered airplane flying at a standard altitude of 4 km. The inlet and exit areas are 0.82 m^2 and 0.45 m^2. The velocity, pressure, and temperature of the exhaust gas are 300 m/s, 230,000 Pa, and 830 K, respectively. Calculate the thrust of the turbojet. Detailed solution pls
The impeller of a centrifugal blower has a radius of 15 cm and a blade width of 6.1 cm at the inlet, and a radius of 30 cm and a blade width of 3.4 cm at the outlet. The blower delivers atmospheric air at 20°C and 95 kPa. Disre- garding any losses and assuming the tangential components of air velocity at the inlet and the outlet to be equal to the impeller velocity at respective locations, determine the volu- metric flow rate of air when the rotational speed of the shaft is 800 rpm and the power consumption of the blower is 120 W. Also determine the normal components of velocity at the inlet and outlet of the impeller.
0il with p = 876 kg/m³ and u = 0.24 kg/m-s is flow- ing through a 1.5-cm-diameter pipe that discharges into the atmosphere at 88 kPa. The absolute pressure 15 m before the exit is measured to be 135 kPa. Determine the flow rate of oil through the pipe if the pipe is (a) horizontal, (b). inclined 8° upward from the horizontal, and (c) inclined 8° downward from the horizontal.
For a fixed compressor inlet velocity and flow area, explain the effect of increasing compressor inlet temperature (i.e., summertime operation versus wintertime operation) on the inlet mass flow rate and the net power output with all other parameters of the problem being the same.
Blowers are used in wastewater treatment plants to assist microorganisms in degrading pollutants. The impeller of a centrifugal blower has a radius of 15 cm and a blade width of 6.1 cm at the inlet, and a radius of 30 cm and a blade width of 3.4 cm at the outlet. The blower delivers atmospheric air at 20°C and 95 kPa. Disregarding any losses and assuming the tangential components of air velocity at the inlet and the outlet to be equal to the impeller velocity at respective locations, determine the volumetric flow rate of air when the rotational speed of the shaft is 800 rpm and the power consumption of the blower is 120 W. Also determine the normal components of velocity at the inlet and outlet of the impeller.
A fluid enters a pipe at speed v1=0.1 m/s. the diameter of the tube is d=200mm and the fluid flowing through the pipe is mercury with a specific gravity of 13.6. the mass flow rate is
Oil with ? = 876 kg/m3 and ? = 0.24 kg/m·s is flowing through a 1.5-cm-diameter pipe that discharges into the atmosphere at 88 kPa. The absolute pressure 15 m before the exit is measured to be 135 kPa. Determine the flow rate of oil through the pipe if the pipe is (a) horizontal, (b) inclined 8° upward from the horizontal, and (c) inclined 8° downward from the horizontal.