over a short period of time the water table lower by 3m. And expected to remain permanently at that Level. Determine the effective vertical stress at depth of 8 and 12m. Below the ground level.(a) immediately after the lowering of water table (b) several years after the lowering of the water table. Explain your answer for each step.

over a short period of time the water table lower by 3m. And expected to remain permanently at that Level. Determine the effective vertical stress at depth of 8 and 12m. Below the ground level.(a) immediately after the lowering of water table (b) several years after the lowering of the water table. Explain your answer for each step.

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter9: Consolidation

Section: Chapter Questions

Problem 9.8P

See similar textbooks

Similar questions

Q A layer of sand extends from ground level to a depth of 9 m and overlies a layer of clay, of very low permeability, 6 m thick. The water table is 6 m below the surface of the sand. The saturated unit weight of the sand is 19 kN/m3 and that of the clay 20 kN/ m3; the unit weight of the sand above the water table is 17 kN/m3. Over a short period of time the water table lowers by 3 m and is expected to remain permanently at this new level. Determine the effective vertical stress at depths of 8 and 12 m below ground level (a)immediately after the lowering of water table and (b)Several years after the lowering of the water table. Explain your answer for each part.
A layer of sand, 4m thick, overlies a layer of low permeability clay, 5mthick. The bulk unit weight of the sand is 16.5 kN/m3 and its saturatedunit weight is 18 kN/m3 . The saturated unit weight of the clay is 21kN/m3 . The water table exists initially at 1.0m below ground level butpumping will permanently and rapidly lower the water table to 3.0mbelow ground level.Determine the variation of total stress and porewater pressure at depthh in the clay and the long-term variation in effective stress.Calculate the initial (before pumping) and the long-term (afterpumping) effective stress at the middle of the clay layer.
A dense silt layer has the following properties: e=0.30, D10=10µm and capillary constant = 0.20cm2 Free ground water level is 8m below the ground surface. Determine the vertical effective stress (kPa) at 5m depth (point A). Assume unit weight of solids = 26.5 KN/m3 and that the soil above the capillary rise and ground surface is partially saturated at 50%.
The profile at a site consists of 5m of sand overlying 10m of compressible clay, which in turn overlies a dense sand. The water table is at the top of the profile. The total unit weight of the top sand is 19kN/m3 and that of the clay is 18kN/m3. The Cv of the clay is estimated to be 5x 10-3 cm2/sec. Initially the clay is normally consolidated. It is planned to place a temporary fill that will exert a vertical load of 200kPa over the entire site. How long must the fill be in place so that, after it is removed, the maximum past pressure at every point in the clay is at least 50kPa larger than the vertical effective stress that existed before the fill was placed?
A dense silt layer has the following properties: e =0.406 D10= 10.1 um Capillary constant = 0.209 sq.cm Free ground water level is 8m below the ground surface. 1.) Find the height of capillary rise in the siltin meters. 2) Find the vertical effective stress at 6m depth. Assume ys = 26.51 kn/m3 and the soil above capillary action rise and ground surface is partially saturated at 79%.
50 ft thick sand is underlain by 25 ft clay. The ground water table, initially at the ground surface, was lowered to a depth of 25 ft below the ground. After such lowering, the degree of saturation of the sand above water table was lowered to 20%. Saturated and dry unit weight of sand are 135 pcf and 116 pcf respectively. The saturated unit weight of clay is 120 pcf. a. what is the unit weight of the sand above the water table after lowering in pcf? b. What is the vertical effective pressure at the midheight of the clay layer when the water table is lowered 50 ft. Below the ground in psf?
The water table in a deep deposit of very fine sand is 1m below the ground surface. Above the water table, the sand is saturated by capillary water. The density of the saturated sand is 2.03 Mg/m³. What is the effective vertical pressure on a horizontal plane at a depth of 4m below the ground surface?
a dense silt layer has the following properties: void ratio = 0.50, effective diameter d10 = 10 um, capillary constant c = 0.20 cm2. free ground water level is 8.0 m below the ground surface. find the vertical effective stress in kpa at 5m depth. assume unit weight of solids = 26.5 kn/m3 and that the soil = 26.5 kn/m3 and that the soil above the capillary action rise and ground surfaces is partially saturated at 50% from the problem above, find the vertical effective stress at 10m depth. assume unit weight of solids=26.5kN/m3 and that the solid above the capillary action rise and ground surface is partially saturated at 50%.
A dense silt layer has the following properties: void ratio e = 0.50, effective Diameter D10 = 10 μm, capillary constant C = 0.20 cm2. The free groundwater level is 8m below the ground surface. Assume unit weight of solids y= 26.50kN/m3. Find the vertical effective stress at 10m depth. Assume that the soil above the capillary zone is partially saturated at 50%.
A layer of soil profile consists of 3.6m upper layer of sand having a saturated unit weight of 18.88 kN/m3 and a lower clay layer 16m deep waith saturated unit weight of 17.31kN/m3. The clayayer has a void ratio of 1.27. The sand layer has a liquidity index of 64.5% and moisture content of 40%. Plastic limit is 20%. Water is located at the ground surface. A tank 12 m high is located at the ground and contains oil with density of 0.81. A. Determine the effective vertical stress at the mid height of clay layer. B. Determine the consolidation settlement of the clay layer. C. Determine the maximum depth that the cylinder be buried so that the settlement will be minimum.
A 5m thick clay layer lies between two layers of sand each 4m thick, the top upper layer being at ground level. The water table is 2m below the ground level but the lower layer of sand is under artesian pressure, the piezometric head being 4m above ground level. The saturated density of clay is 20kN/m3 and that of sand is 19kN/m3 . Above the water table, unit weight of sand is 16.5kN/m3 . Calculate the effective vertical stress at the top and bottom of the clay layer.
The profile at a site consists of 5 m of sand overlying 10 m of compressible clay, which in turn overlies a dense sand. The water table is at the top of the profile. The total unit weight of the top sand is 19 kN/m3, and that of the clay is 18 kN/m3. The cv of the clay is estimated to be 5 x 10-3 cm2/sec. Initially the clay is normally consolidated. It is planned to place a temporary fill that will exert a vertical load of 200 kPa over the entire site. How long must the fill be in place so that, after it is removed, the maximum past pressure at every point in the clay is at least 50 kPa larger than the vertical effective stress that existed before the fill was placed?