Only part C plz A reservoir supplies water as shown in Fig. 1. The pipe system consists of 6 m of pipe and two 90° elbows.All pipe is 50 mm diameter, which made from cast iron.ZiBall ValveZz 5 cmZ3 = 0Figure 1: Schematic diagram of task 1.Part AIf the system is assumed to be frictionless and the water level in the reservoir is 15 cm (Z= 20cm):Using Bernoulli's equation, find the water velocity at the pipeline exit.Detennine the Reynolds number in the pipe system and the significance of this Information.4HTU.Al Hussein Technical UniversityPart BTaking in your consideration the head losses accumulated by the fluid when flowing in the pipeline:Now determine water velocity at the pipeline exit as a function of time.Note that friction factor f can be calculated by using Blasius formula (f = (100 * Re )025 ) ifReynolds number is less than 105Part CAlso, a turbine can be used before the pipeline exit to produce electricity.If the used turbine converts only two-thirds of the energy that the fluid will lose after passing throughthe turbine, what is the efficiency of this turbine?Identify the most common water turbines and the limitations that exist within these diferent types?Although hydraulic turbines considered one of the most efficient power plants, thcir ecological impactis a big concern. Discuss this issue and suggest remedies for such problems by writing a shortparagranh?

Answered: Image /qna-images/answer/383298db-69a7-4d0c-96db-642cc794ce7a.jpg

Part C Also, a turbine can be used before the pipeline exit to produce electricity. If the used turbine converts only two-thirds of the energy that the fluid will lose after passing through the turbine, what is the efficiency of this turbine? Identify the most common water turbines and the limitations that exist within these different types? Although hydraulic turbines considered one of the most efficient power plants, their ecological impact is a big concerm. Discuss this issue and suggest remedies for such problems by writing a short paragranh?

Part C Also, a turbine can be used before the pipeline exit to produce electricity. If the used turbine converts only two-thirds of the energy that the fluid will lose after passing through the turbine, what is the efficiency of this turbine? Identify the most common water turbines and the limitations that exist within these different types? Although hydraulic turbines considered one of the most efficient power plants, their ecological impact is a big concerm. Discuss this issue and suggest remedies for such problems by writing a short paragranh?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

thi 40 A vertical sluice gate (4m) wide and (3m) deep contains water on both of its sides. On the upstream side, the water is (6m) deep and on the downstream side it is (2.5m) deep from the bottom of the sluice. What is the resultant pressure force on the gate and the position of this resultant force from the hinge
Drive formula for increas in volume of a thin metalic sphere when if is subjected to an internal pressure P. If diameter of thin sphere is 400 mm, thickness, t= 2 mm and is just full of water at atmosphere. Calculate the volume of water pumped in to raise the inside pressure to 1.5 N/mm², E=100 kN/mm³, K=2.5 kN/mm², v=0.25.
The hydrostatic pressure in a 24" diameter ductile iron water main is 75 p.s.i. If the thickness of the iron is 1/2", then what is the tension in the iron due to the hydrostatic pressure in p.s.i ?
Water is pumped through a vertical 2-in. new galvanized-iron pipe to an elevated tank on the roof of a building. The pressure on the discharge side of the pump is 200 lb per sq in. What pressure can be expected at a point in the pipe 250 ft above the pump when the flow is 150 gpm? Answer should be: 37 lb per sq. inch Show your handwritten solution, thank you.
A vertical cylindrical tank has an orifice for its outlet. When the water surface in the tank is 5m above the orifice, the surface can be lowered 4m in 20 minutes, the pressure on the surface being atmospheric. What uniform air pressure must be applied to the surface if the same volume of water is to be discharged in 10 minutes?
Pressure loss along a pipe pumping water is 6.6Pa. If the pipe is 2.1m long, what angle (in degrees) must it be orientated to the horizontal to overcome the pressure drop?
Fluid mechanics If the hydrostatic pressure at the bottom of the cylindrical tank is 14.715 kPa, specific gravity of the tank is 0.15, and the weight of the tank is 25 kN, find the pressure at the bottom of the tank if the tank has to be lain sideways?
Show the solution. A boiler requires 75,000 m³/hr of standard air. What is the motor power if fan can deliver a total pressure of 145 mm of water gage. The mechanical efficiency is 64%.
1. Estimate the height to which water will rise in a capillary tube of diameter 4mm of the surface tension is 0.085 N/m and the contact angle is zero degrees? 2. Compute the capillary depression for mercury in a glass capillary tube 3mm in diameter if the surface tension of mercury is 0.625 N/m and the wetting angle is 135 degrees. Given the specific gravity of mercury is 13.6.
Solve the problem below
Problem 3: Water issues from a hole in a large tank, as shown in the attached figure.Assuming frictionless flow, find L.
Subject is hydraulics A closedcylindrical vessel 5 ft in diameter and 6 ft high is 3/4 filled with molasses(SG = 1.24) and rotated about its vertical axis. Air is pressurized at 14.5psi. a. If w = 50 rpm, solve for thepressure at the base at the circumference of the vessel b. If w = 75 rpm, solve for thepressure at the base at the circumference of the vessel c. Solve for w (in rpm) so that thereis no water at the base of the vessel within 1.8 ft radius