Phase Behavior of Elemental Gallium: Gallium (Ga) is one of the few metals that is liquid near room temperature (Tm = 302 K). a) The vapor pressure for Ga has been measured at 100 Pa at 1620 K and 10 kPa at 2125 K. What is the average metal-metal bond strength (in kJ/mol) for Ga assuming a liquid state coordination number of 6? b) What is the boiling point ( in K) for Ga in a standard lab at sea-level given the above information

Phase Behavior of Elemental Gallium: Gallium (Ga) is one of the few metals that is liquid near room temperature (Tm = 302 K). a) The vapor pressure for Ga has been measured at 100 Pa at 1620 K and 10 kPa at 2125 K. What is the average metal-metal bond strength (in kJ/mol) for Ga assuming a liquid state coordination number of 6? b) What is the boiling point ( in K) for Ga in a standard lab at sea-level given the above information

Principles of Modern Chemistry

8th Edition

ISBN:9781305079113

Author:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Publisher:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Chapter22: Inorganic Materials

Section: Chapter Questions

Problem 40AP

See similar textbooks

Similar questions

Lattice parameters of α and β phases were calculated from x-ray diffraction measurements performed in A-B alloys with different compositions, all quenched from 500, 600 and 700 °C. Draw a schematic A-B phase diagram using this information
For a Copper-Nickel (Cu-Ni) alloy of composition 25 wt % Ni and 75 wt % Cu at 1200 OC (Point B), refer to the phase diagram provided in Figure 2 and answer the following. (i) What is composition of liquid phase? (ii) What is composition of solid phase? (iii) What fraction of the system is liquid for a 25% Ni alloy at 1250 OC? (iv) What fraction of the system is solid for a 25% Ni alloy at 1250 OC?
Fluorite (CaF2) has a face centered cubic structure, space group 225, with network parameter equal to 5.45 Å), with four CaF2 units per cell unitary (Ca+ at site 4a(0,0,0) and F- at site 8c(1/4.1/4.1/4 and 3/4.3/4.3/4) + face centered cubic lattice translations for both ions). a) Get a simplified expression for the structure factor F(hkl) of fluorite. (b) What condition must be fulfilled by the Miller indices h,k,l in such a way that F(hkl) ≠ 0?
In the iron-carbon alloy phase diagram as shown in Fig. 1, draw the microstructures with indicating the name of each phases existing at (a) - (h) point.
What point defects are possible for Al2O3 as an impurity in MgO? How many Al3+ ions must be added to form each of these defects? Explain.
Discuss glass transition temperature and the factors affecting GTT and what are its significances. Give detailed answer please
Cu and Ni form a substitutional solidsolution. This means that the crystal structureof a Cu-Ni alloy consists of Ni atomssubstituting for Cu atoms in the regularatomic positions of the FCC structure. Fora Cu-30% wt.% Ni alloy, what fraction ofthe atomic sites does Ni occupy?
Nickel, aluminum and copper have face centered cubic structure yet Ni is soluble in Cu whereas Al has only limited solubility. Explain so, and also the cooling curve of a binary alloy looks exactly similar to that of a pure metal is this possible?
6.1) At the composition of 0.77% by weight C, identify the phase(s) presentat 950 degrees C 6.2) When the specimen is at 950 degrees C, what is the maximum C composition at which a single phase Austenite is stable?6.3) If we slowly cool a Fe-C alloy with 0.77% by weight C, austenitized at950 degrees C, to just below the eutectoid temperature of 727 degrees C, give the weight percentage and composition of the phases present based on the phase diagram given above6.4) If we cool very quickly a Fe-C alloy with 0.77% by weight C,austenitized at 950 degrees C, to room temperature, give the weight percentage and composition of the phase(s) present
List three main types of crystal structure systems in metals, and illustrate the main differences between Body Centred Cubic, Face Centred Cubic and Hexagonal Close Packed structures, in terms of the atomic plane arrangements, Coordinate Number (CN) and Atomic Packing Factor (APF) calculations, with giving metal examples for each type and explain the effect of this difference on the metal properties
PHASE DIAGRAMS CALCULATIONS THERE IS NO BETA PHASE (THEORETICAL DIAGRAM ATTACHED BELOW) Please explain answers for each part of question. i) What is the point X on the diagram called? ii) What is the composition of the alloy at this point? iii) What is the name given to the line Y? iv) What is the melting point of pure B? v) What is the maximum solubility of α in the β phase? vi) An alloy with a composition of 76 wt% A is a liquid at 350 °C. At which temperature will solid begin to form and at which temperature will it become completely solid? vii) For a 70 wt% A alloy determine the composition of the solid and liquid phases at 200 °C? viii) Considering the same alloy composition calculate the phase fraction of the solid and liquid phases at the same temperature.
If you want to determine the glass transtion tempreture (Tg), softening point (Ts), melting point (Tm) and crystallization temperatures (Tc) of the glass-ceramics which characterization techniques can be used? Plase expain in details.