In Fig. 12-40, one end of a uniform beam of weight 222 N is •23 hinged to a wall; the other end is supported by a wire that makes angles 0 = 30.0° with both wall and beam. Find (a) the tension in the wire and the (b) horizontal and (c) vertical components of the force of the hinge on the beam. Hinge Figure 12-4o Problem 23. 347 / 1368

In Fig. 12-40, one end of a uniform beam of weight 222 N is •23 hinged to a wall; the other end is supported by a wire that makes angles 0 = 30.0° with both wall and beam. Find (a) the tension in the wire and the (b) horizontal and (c) vertical components of the force of the hinge on the beam. Hinge Figure 12-4o Problem 23. 347 / 1368

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter14: Static Equilibrium, Elasticity, And Fracture

Section: Chapter Questions

Problem 41PQ: In Example 14.3, we found that one of the steel cables supporting an airplane at the Udvar-Hazy...

See similar textbooks

Related questions

Q: 3. End A of the bar AB in Fig. 11.39 rests on a frictionless horizontal surface, and end B is…

A: The normal force on the rod is given by N=F×43=120×43=160 N

Q: "A trap door in a ceiling is 0.91 m square, has a mass of 11 kg, and is hinged along one side, with…

A: a) The torque around the hinge point is,

Q: A uniform rod is attached to a wall by a hinge at its base. The rod has a mass of 6.0 kg, a length…

A: (a)Refer the free body diagrams given below.

Q: one end of a uniform beam of weight 222 N is hinged to a wall; the other end is supported by a wire…

Q: The figure shows three boards clamped together. The center board weighs 93.5 N, and the coefficient…

A: The figure shows the force acting on the three boards clamped together.

Q: In Fig. 12-45, suppose the length L of the uniform bar is 3.00 m and its weight is 200 N. Also, let…

A: In Given figure the length L of the uniform bar is 3.0 m and its weight is 200 N. Also, let the…

Q: 1 Figure 12-15 shows three situations in which the same horizontal rod is supported by a hinge on a…

Q: A uniform board is suspended from a ceiling and supported horizontally by two wires, A and B. The…

A: Draw the free body diagram

Q: 12-23. If the wide-flange beam is subjected to a shear of V = 30 kN, determine the maximum shear…

Q: A non-uniform rod of length 1.00 m is hung horizontally, supported by strings on both ends. If the…

Q: A uniform drawbridge must be held at a 38.5 ∘∘ angle above the horizontal to allow ships to pass…

A: Given data-

Q: In the figure, suppose the length L of the uniform bar is 3.00 m and its weight is 200 N. Also, let…

Q: A 1.323-N uniform beam is attached to a vertical wall at one end and is supported by a cable at the…

Q: One end of a uniform rod of weight w = 73.5 N and length L = 2.55 m is supported by a cable at an…

A: Given Data : The weight of the rod is given as w = 73.5N. The length of the rod is given as L =…

Q: Suppose a person’s femoral diaphysis is idealized as a circular cylinder with a periosteal diameter…

Q: A horizontal plank 4.64 m long and having mass 23.0 kg rests on two pivots, one at the left end and…

Q: A uniform horizontal beam with a length of 8.00 m and a weight of 200 N is attached to a wall by a…

Q: . One end of a steel rod of radius R = 9.5 mm and length L = 81 cm is held in a vise. A force of…

Q: a vertical uniform beam of length Lthat is hinged at its lower end.A horizontal force F is applied…

A: Here we use Newton's second law, Along the x-axis, we get as below. Fa-T Cos ϴ - Fh = 0 Now using…

Q: Figure 12-29 Problem 11. •12 In Fig. 12-30, trying to get his car out of mud, a man ties one end of…

A: Length of rope (L) = 18 m Applied force (F) at the midpoint of rope = 550 N vertical displacement…

Q: In the figure, suppose the length L of the uniform bar is 2.9 m and its weight is 170 N. Also, let…

A: In the figure it is given that a weight of 270 newton is placed on a a uniform bar of length 2.9 m…

Q: A uniform beam of mass M = 10.0 kg and length L = 2.00 m is suspended from a ceiling at an angle of…

A: Mass of the beam is m = 10 kg Length of the beam is L = 2 m Angle of beam with ceiling is 30 degrees…

Q: •19 To crack a certain nut in a nutcracker, forces with magnitudes of at least 40 N must act on its…

A: Given F = 40N L = 12cm d= 2.6cm To find force ating perpendicular to the Handel's

Q: A uniform L = 6.71 m long horizontal beam that weighs WB= 363N is attached to a wall by a pin…

Q: a uniform rod of mass m is hinged to a building at its lower end, while its upper end is held in…

A: The tensions in the rope,

Q: A uniform 22 kg beam, 3.0 m long, is attached to a wall on the left by a hinge, and is supported by…

Q: A uniform ladder of mass (m = 13.5 kg) and length (L) leans against a frictionless wall. If the…

Q: 21. Go The drawing shows a uniform horizontal beam attached to a vertical wall by a frictionless…

A: Let the force exerted by the brace is given as Fb along its direction of length also the two…

Q: what is the tension in the wire?

A: Given:

Q: •19 To crack a certain nut in a nutcracker, forces with magnitudes of at least 40 N must act on its…

Q: Problem 4.4 The uniform, horizontal beam shown in Fig. 4.51 is hinged to the wall at point A and…

Concept explainers

Rotational Equilibrium And Rotational Dynamics

In physics, the state of balance between the forces and the dynamics of motion is called the equilibrium state. The balance between various forces acting on a system in a rotational motion is called rotational equilibrium or rotational dynamics.

Equilibrium of Forces

The tension created on one body during push or pull is known as force.

Question

Hi I need help I need to understand this problem please thank you

In Fig. 12-40, one end of a uniform beam of weight 222 N is
•23
hinged to a wall; the other end is supported by a wire that makes angles 0
= 30.0° with both wall and beam. Find (a) the tension in the wire and the
(b) horizontal and (c) vertical components of the force of the hinge on the
beam.
Hinge
Figure 12-4o Problem 23.
347
/ 1368

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

a vertical uniform beam of length Lthat is hinged at its lower end.A horizontal force F is applied to the beam at distance y from the lower end. The beam remainsvertical because of a cable attached at the upper end, at angle uwith the horizontal. gives the tension T in the cableas a function of the position of the applied force given as a fractiony/L of the beam length.The scale of the T axis is set by Ts= 600 N.Figure 12-49c gives the magnitude Fh of the horizontal force on thebeam from the hinge, also as a function of y/L. Evaluate (a) angle uand (b) the magnitude of .
One end of a uniform rod of weight w = 73.5 N and length L = 2.55 m is supported by a cable at an angle of ? = 37.0°above the rod. The other end rests on a small frictionless support and presses into a wall as shown in the figure. Determine the magnitude n of the vertical normal force exerted by the support on the rod and find the magnitude T of the tension in the cable.
a uniform rod of mass m is hinged to a building at its lower end, while its upper end is held in place by a rope attached to the wall. If angle u1 = 60°, what value must angle u2 have so that the tension in the rope is equal to mg/2?
A sign is supported by a uniform horizontal boom of length 3.10 m and weight 72.0 N. A cable, inclined at an angle of 16 °with the boom, is attached at a distance of 2.71 m from the hinge at the wall. The weight of the sign is 108.0 N. What is the tension in the cable and what are the horizontal and vertical forces Fx and Fy exerted on the boom by the hinge? Comment on the magnitude of Fy. T= In N Fx= in N Fy= in N The magnitude of Fy is select (small or large) compared to that of Fx and T.
A uniform ladder of mass (m= 13.5 kg) and length (L) leans against a frictionless wall. If the angle ©60.0°, find the static friction force between the ladder and the floor when a 60.0-kg person stands two-third of the wayup the ladder?
A uniform L = 6.71 m long horizontal beam that weighs WB= 363N is attached to a wall by a pin connection that allows the beam to rotate. Its far end is supported by a cablewith tension Tthat makes an angle of 50.0° with the horizontal, and a person of weight WP= 427.5N is standing d = 2.38m from the pin. Find the magnitude of the force R exertedon the beam by the wall if the beam is in equilibrium. A)532N B)534N C)536N D)538N
A uniform horizontal beam with a length of ℓ = 8.00 m and a weight of Wb =200 N is attached to a wall by a pin connection. Its far end is supported by a cable that makes an angle of φ = 53.0° with the beam (as shown). A person of weight Wp = 600 N stands a distance d = 2.00 m from the wall. Find the tension in the cable as well as the magnitude and direction of the force exerted by the wall on the beam.
suppose the length L of the uniform bar is 3.4 m and its weight is 180 N. Also, let the block's weight W = 310 N and the angle 0 = 41°. The wire can withstand a maximum tension of 440 N. (a) What is the maximum possible distance x before the wire breaks? With the block placed at this maximum x, what are the (b) horizontal and (c) vertical components of the force on the bar from the hinge at A?
A uniform horizontal beam 5.00 m long and weighting 3.03 102 N is attached to a wall by a pin connection that allows the beam to rotate. Its far end is supported by a cable that makes an angle of 53.0° with the horizontal (Figure (a)). If a person weighing 6.05 102 N stands 1.60 m from the wall, find the magnitude of the tension in the cable and the force exerted by the wall on the beam. T = N Rx = N Ry = N Even if we selected some other axis for the torque equation, the solution would be the same. For example, if the axis were to pass through the center of gravity of the beam, the torque equation would involve both T and Ry. Together with Equations (1) and (2), however, the unknowns could still be found—a good exercise. In this example, notice the steps of the Problem-Solving Strategy could be carried out in the explicit recommended order.QUESTION What happens to the tension in the cable if the man in Figure (a) moves farther away from the wall? The tension would…
A uniform beam of length L = 11.7 meters and mass of 109.3 kg is pinned at one end and is being supported by a wire as shown. The wire is connected to the beam x = 3.3 meters from the pin. A person of mass 81.6 kg is standing all the way out on the edge of the beam. If θ = 17.3 degrees and φ = 79.4 degrees, what is the tension in the wire?
The system is in equilibrium. A concrete block of mass 225 kg hangs from the end of the uniform strut of mass 45.0 kg. A cable runs from the ground, over the top of the strut, and down to the block, holding the block in place. For angles f = 30.0° and u = 45.0°, find (a) the tension T in the cable and the (b) horizontal and (c) vertical components of the force on the strut from the hinge.
Two ladders, 4.00 m and 3.00 m long, are hinged at point A and tied together by a horizontal rope 0.90 m above the floor. The ladders weigh 480 N and 360 N, respectively, and the center of gravity of each is at its center. Assume that the floor is freshly waxed and frictionless. (a) Find the upward force at the bottom of each ladder. (b) Find the tension in the rope. (c) Find the magnitude of the force one ladder exerts on the other at point A. (d) If an 800-N painter stands at point A, find the tension in the horizontal rope.