Potassium nitrate was synthesized in an experiment using 10 mL of nitric acid and excess potassium hydroxide. The mass data obtained from the experiment is shown in Table 1 below. Given that the percentage yield of potassium nitrate was 88.3 %, calculate the concentration (% m/v) of the nitric acid used in the experiment. Table 1: Mass data for the synthesis of potassium nitrate from nitric acid and potassium hydroxide Mass of clock glass and crystallized potassium nitrate/ g 45.55 Mass of empty clock glass/ g 39.18

Potassium nitrate was synthesized in an experiment using 10 mL of nitric acid and excess potassium hydroxide. The mass data obtained from the experiment is shown in Table 1 below. Given that the percentage yield of potassium nitrate was 88.3 %, calculate the concentration (% m/v) of the nitric acid used in the experiment. Table 1: Mass data for the synthesis of potassium nitrate from nitric acid and potassium hydroxide Mass of clock glass and crystallized potassium nitrate/ g 45.55 Mass of empty clock glass/ g 39.18

Chemistry & Chemical Reactivity

10th Edition

ISBN:9781337399074

Author:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Publisher:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Chapter11: Intermolecular Forces And Liquids

Section11.6: Properties Of Liquids

Problem 1.2ACP

See similar textbooks

Similar questions

A student determined fluoride in a toothpaste sample using ion chromatography. A toothpaste sample of mass 0.100 g was dissolved in type I water and then quantitatively filtered through a Whatman #1 filter paper into a clean 100 ml volumetric flask. The flask was then made up to volume with type I water and mixed thoroughly.A portion of the solution was filtered through a 0.45 um filter into a sample vial for analysis. Analysis of the sample gave a fluoride concentration of 1.60 mg/l Calculate the % w/w fluoride in the original toothpaste sample. (Give your answer to 3 decimal places please)
The three sets of units for expressing density (or concentration, as in “mass of solute per unit volume of solvent”) below are equivalent: kg⁄L = g⁄mL =g cm! ⁄a) Using dimensional analysis, show that the above expression is true.b) What is 1.0 kg⁄L = 1.0 g⁄mL = 1.0 g cm! ⁄ expressed in SI base units?
Stock iron(II) solution (200Ug mL-1 Fe) ferrous ammonium sulfate hexahydrate mass= 0.1437g, transfer it to a 100 ml beaker. add 15 ml approx of water and 15m1 'approx of dilute sulphuric acid (2M H2SO.). then transfer FeII to 100 ml flask makeup to the mark with water. calculate the moles of ferrous ammonium sulfate hexahydrate solution in unit ug/mL.
Produce Water mass “X” is known to be a mixture of water masses “1”, “2”, and “3”. Using the data plotted below, calculate the composition of “X” (i.e. determine the fraction from each of the 3 water masses that makes up water mass X). Watermass#1– SF6 =25 S=33.5 Watermass#2– SF6 =75 S=32 Watermass#3– SF6 =50 S=36.5 Water mass X – SF6 =60 S= 34
In biological systems, enzymes are used to accelerate the rates of certain biological reactions. Glucoamylase is an enzyme that aids in the conversion of starch to glucose (a sugar that cells use for energy). Experiments show that 1 μg mol of glucoamylase in a 4% starch solution results in a production rate of glucose of 0.6 μg mol/(mL)(min). Determine the production rate of glucose for this system in units of lb mol/(ft3)(day). A. 0.0015 lb mol/(ft3)(day) B. 0.0315 lb mol/(ft3)(day) C. 0.0539 lb mol/(ft3)(day) D. 0.3569 lb mol/(ft3)(day)
Complete the following statements. You may find the flowchart in section 1.2 of your textbook helpful. In station C.... The provided aqueous KI/I2 was a The provided solid Na2S2O3 was a Options Pure element Pure compound Homogeneous Heterogeneous
1. Which of the following is not a step in preparing a water sample container?a. All sample containers must be dark in colorb. The type of sample container and the level of cleaning required depend on the type of sample to be takenc. All sample containers must be thoroughly cleaned in the laboratory before sampling is carried outd. The number of containers prepared must always be in excess of what is needed, for quality assurance, quality control and reserves 2. The purpose of environmental sample analysis is..a. To determine the origin and concentration of chemicals in the environmentb. To determine the origin, concentration of chemicals and/or pollutants in the environmentc. To determine the concentration of a chemical in the environmentd. To determine the cause and concentration of pollutants in the environment
Chemistry A group of students was tasked with synthesizing dibenzalacetone (DBA) in the lab. They used acetone as limiting reagent, calculated their TY to be 8.0 g DBA, obtained 14.0 g crude product (wet) and their % Yield was 65%. What was the actual yield for their final product (recrystallized, dry DBA)? What was the minimum volume (ml) of ethanol they needed to recrystallize their wet crude? What was the amount of impurities (side products, moisture,...) contained in their wet crude?
7. After performing precipitation gravimetry, Asta placed the weighing form inside the crucible, heated it, cooled it down, and weighed the crucible with the weighing form and obtained a mass of 23.4120 g. Repeating this cycle continuously gave a mass of 23.2125 g, then 23.1136 g, then 23.1139 g. Which among these masses should he use for his calculations?
Convert and use sig figs 254.3g to kg
You take a representative soil sample and determine the following data: Exchangeable cation cmolc/kg of soil Ca2+ 2.7 Mg2+ 1.0 K+ 0.1 H+ 1.0 Al3+ 2.8 Na+ 0.1 1) What is the CEC (cmolc/kg ) of this soil?
Calculate the percent composition of sand in the mixture using the mass of the recovered sandCalculate the theoretical mass of salt in the mixtue using the mass of the recovered sandCalculate the theoretial percent composition of salt in the mixtureCalculate the percent error for the recovered saltCalculate the total mass of the recovered solids Weight of mixture: 1.841Weight of salt: 1.319Weight of sand: 0.376Weight of sand after heating: 0.376