Phenobarbital was introduced in 1912 for the treatment of epilepsy. It is an anti-convulsant and sedative-hypnotic drug and used to control seizures. The measurement of phenobarbital is by fluorescence method. A 5.00 mL aliquots of an unknown containing phenobarbital were delivered to 50.00 mL volumetric flasks. The following volumes of a standard solution of phenobarbital, 2.00ug/mL, were then introduced to the volumetric flasks before diluting to volume with the corresponding signals on a fluorometer equipment. Find the concentration of phenobarbital in the original unknown sample.

Phenobarbital was introduced in 1912 for the treatment of epilepsy. It is an anti-convulsant and sedative-hypnotic drug and used to control seizures. The measurement of phenobarbital is by fluorescence method. A 5.00 mL aliquots of an unknown containing phenobarbital were delivered to 50.00 mL volumetric flasks. The following volumes of a standard solution of phenobarbital, 2.00ug/mL, were then introduced to the volumetric flasks before diluting to volume with the corresponding signals on a fluorometer equipment. Find the concentration of phenobarbital in the original unknown sample.

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter31: Introduction To Analytical Separations

Section: Chapter Questions

Problem 31.26QAP

See similar textbooks

Similar questions

A chemist obtained the following data for percent lindane in the triplicate analysis of an insecticide preparation: 7.23, 6.95, and 7.53%. Calculate the 90% confidence interval for the mean of the the three data, assuming that (a) the only information about the precision of the method is the precision for the three data. (b) on the basis of long experience with the method, it is believed that s---->σ lindane. (c) If s=0.28 is good estimate of σ, how many replicate measurement should be made in order for the mean for the analysis of sample to be within 0.2% of the true mean 90% of the time.
a. Briefly explain why internal standardization method is useful inanalytical chemistry?b. Why does a response factor of an instrument’s detector need to becalculated?
What effect will the following have on plate height (H). Make sure to explain your full and complete reasoning. Reducing the rate of sample injection.
Calculate Trial I, Trial II, Trial III Vol.Ag(NO3)Added.
A silver-30%gold alloy sample (cylindrical with 1 cm diameter and 0.3 cm height) is subjected to a selective silver dissolution in 0.1 M HNO3 at current density of 2.5 mA/cm2 . How long will it take until the total amount of silver is dissolved? Assume in average a density of 12 g/cm3 for the alloy sample.
The partition coefficient of ammonia between water and chloroform is wanted to be determined. The necessary quantities of ingredients are taken into the separation funnel, and the extraction process is applied. At the end of the extraction process, 5 mL portions of each of the water and chloroform phases are titrated with 0.1 M HCI in the presence of methyl orange indicator. If the volumes spent at the turning points are 7.2 and 5.1 mL, respectively, calculate the KSU, KLOROFORM (Dispersion coefficient) value.
Calculate the retardation factor (Rf) for dissolved Tetrachloroethene contamination given the bulk density of soil is 2.4 gm/cc, fraction organic content (foc) of soil is 0.005, and the Organic Carbon Partition Coefficient (Koc) is the number you look up in the table. HInt: Use Fetter Equation (Koc = Kd /foc to calculate Kd. Group of answer choices 1.4 to 2.7 l/gm 1.08 to 1.2 Cannot be calculated from given information. 3.25 to 4.5 1.05 to 1.2 l/gm
Compare and contrast an anticipatory standard to a reactionary standard by listing and describing some advantages and disadvantages.
which of the folowing(s) is/are true ? 1 split ratio in GC is a ratio of sample passed to column to amount of mobile phashe 2 column resolution decreases with increasing column lenght 3 decreasing the tube diameter ,increases the resolution
Can you please fill the rest of tghe data based on the on inforamtion you have and answer Average percent by mass of acetic acid in vinegar sample (%) ________________ Standard deviation of percent by mass of acetic acid in vinegar sample (%)
what can be an analyte for using internal standard? sample: vegetable oil containing ethyl oleate, IS: Ethyl oleate. what should be analyte here (what mixture composions) to use for internal standard method and calibration?
Potassium dichromate has several industrial applications. To determine the purity of the salt that will be used in different industrial processes, a sample mass equal to 2.660 g was dissolved and quantitatively transferred to a 500.00 mL flask. An aliquot of 25.00 mL of this solution was treated with excess KI and the released iodine was titrated with 0.1000 mol L-1 sodium thiosulfate, spending 27.00 mL. Calculate the purity of the analyzed salt. Data:K = 39.10 O = 16.00 Cr = 52.00 I = 126.9 S = 32.07