Potassium nitrate was synthesized in an experiment using 10 mL of nitric acid and excess potassium hydroxide. The mass data obtained from the experiment is shown in Table 1 below. Given that the percentage yield of potassium nitrate was 88.3 %, calculate the concentration (% m/v) of the nitric acid used in the experiment. Table 1: Mass data for the synthesis of potassium nitrate from nitric acid and potassium hydroxide Mass of clock glass and crystallized potassium nitrate/ g 45.55 Mass of empty clock glass/ g 39.18

Potassium nitrate was synthesized in an experiment using 10 mL of nitric acid and excess potassium hydroxide. The mass data obtained from the experiment is shown in Table 1 below. Given that the percentage yield of potassium nitrate was 88.3 %, calculate the concentration (% m/v) of the nitric acid used in the experiment. Table 1: Mass data for the synthesis of potassium nitrate from nitric acid and potassium hydroxide Mass of clock glass and crystallized potassium nitrate/ g 45.55 Mass of empty clock glass/ g 39.18

Chemistry & Chemical Reactivity

10th Edition

ISBN:9781337399074

Author:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Publisher:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Chapter11: Intermolecular Forces And Liquids

Section11.6: Properties Of Liquids

Problem 1.2ACP

See similar textbooks

Similar questions

Common soda-lime-silica glass is made by melting together Na2CO3, CaCO3, and SiO2. The carbonates break down, liberating CO2 gas bubbles that help to mix the molten glass. For 1,000 kg of container glass (15 wt% Na2O, 10 wt% CaO, 75 wt % SiO2), calculate the raw material batch formula. What is the weight percent of SiO2?
A student determined fluoride in a toothpaste sample using ion chromatography. A toothpaste sample of mass 0.100 g was dissolved in type I water and then quantitatively filtered through a Whatman #1 filter paper into a clean 100 ml volumetric flask. The flask was then made up to volume with type I water and mixed thoroughly.A portion of the solution was filtered through a 0.45 um filter into a sample vial for analysis. Analysis of the sample gave a fluoride concentration of 1.60 mg/l Calculate the % w/w fluoride in the original toothpaste sample. (Give your answer to 3 decimal places please)
Why is water not used as a solvent in extraction of nuts
1. State the process that is used to separate kerosene and diesel fuel. State the operating conditions of this process. 2. State the process that can be used to yield fraction of heavy fuel oil from crude oil. 3. Describe the difference between straight run naptha and cracked naptha.
Calculate the mass of CaCl2 needed to prepare 25 mL of 0.5M CaCl2. Clearly show your calculations and unit cancellation.
What is the function of a desiccant in a set-up of volatilization gravimetry? To remove nitrogen from the sample To remove sulfuric acid from the sample To remove water vapor from the sample To remove carbon dioxide from the sample
The procedure for the synthesis of menthone indicates that you should use 10 cm³ of 6M sulphuric acid. Suppose that only sulphuric acid with concentration 1.5M is available in the laboratory. What volume in cubic centimetres of this solution do you need to add to the reaction mixture to replace the solution originally specified? [Do not type in the unit. Round the answer to a whole number.] *
From the practical standpoint, is it better to use a "good" solvent or a "poor" solvent when measuring polymer molecular weight? Explain.
Cloth can be waterproofed by coating it with a silicone layer. This is done by exposing the cloth to (CH3)2SiCl2 vapor. The silicon compound reacts with OH groups on the doth to form a waterproofing film (density = 1.0 g/cm3) of [(CH3)2SiO]n, where n is a large integer number. n (CH3)2SiCl2 + 2n OH 2n Cl + n H2O + [(CH3)2SiO]n The coating is added layer by layer, with each layer of [(CH3)2SiO]n being 0.60 nm thick. Suppose you want to waterproof a piece of doth that is 3.00 square meters, and you want 250 layers of waterproofing compound on the cloth. What mass of (CH3)2SiCl2 do you need?
Explain the terms sorption and desorption.
Using the percent purity calculations, determine the percent yield of synthesis of aspirin. Part I Synthesis of Aspirin Mass of salicylic acid used (g) 2.029g Volume of acetic anhydride used (mL) 5ml Mass of acetic anhydride used (vol. × 1.08 g/mL) 5.4g Mass of aspirin synthesized (g) 3.256g Part II Melting Temperature Data Melting temperature (°C) 133°C Part III Salicylic Acid Standard Stock Solution Initial mass of salicylic acid (g) 0.210g Moles of salicylic acid (mol) 0.0147 mol Initial molarity of salicylic acid (M) 0.724 M Part III Beer’s Law Data for Salicylic Acid Standard Solutions Trial Concentration (M) Absorbance Water (mL) 1 10 0.301 0 2 7.5 0.219 2.5 3 5.0 0.163 5.0 4 2.5 0.074 7.5 Best-fit line equation for the salicylic acid standards Test of the Purity of the Synthesized Aspirin Initial mass of aliquot of product (g)…
What are refractories? How are they classified?. Give examplesfor each type.