Presents the diagram of the problem, necessary formulas, clearance and numerical solution: A metal plate 4 mm thick has a temperature difference between its two faces of 32 ◦C. It transmits 200 kcal/h through an area of 5 cm2. Calculate the thermal conductivity of the metal in W/m K.

Presents the diagram of the problem, necessary formulas, clearance and numerical solution: A metal plate 4 mm thick has a temperature difference between its two faces of 32 ◦C. It transmits 200 kcal/h through an area of 5 cm2. Calculate the thermal conductivity of the metal in W/m K.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.4P: 1.4 To measure thermal conductivity, two similar 1-cm-thick specimens are placed in the apparatus...

See similar textbooks

Related questions

Q: Consider a person riding their bicycle who is pedaling forward in the +i direction at a constant…

Q: A force couple system located at point O is shown in the figure. Determine the coordinates of the…

A: Find the coordinates of point P.

Q: 25-lb block has an initial speed of v0 = 10 ft/s when it is midway between springs A and B. After…

Q: 2. A circular frustum of cone made of iron is one meter high with diameters 0.60m at the base and…

Q: A cone clutch is to transmit 30 kW at 1250 rpm. The face angle of the cone clutch is 12.5o and the…

Q: (e) Out of the camber and caster, which is measured first and why? How the cambe angle can be…

A: Tire wear on the outside tread of the tyre is caused by positive camber. A car will pull to the…

Q: Ex- If the flowrate between two tanks is (e.s m/s). find CH)? KL1.8 Ls Soom LIE30 DI=300 Dg = S0o mm…

Q: For the shaft shown in the figure below, compute the angle of twist of pulleys B and C relative to…

Q: Design a compression coupling for a shaft to transmit 2000 N-m. The allowable shear stress for the…

Q: The function p. = e ($1, $2) gives the position of the end-effector of the following kinematic chain…

Q: A triangular plate and two rectangular plates are welded to a straight bar AB. The welded unit…

A: Solution; Given Data: ω=7.5 rad/s Co-ordinates of different corners are: A: 04000B: 00300C:…

Q: In the attached stress-strain curve, the approximate value for the strain at yield: 400- 300- 200-…

A: Find the strain at yield point. Draw a perpendicular from the point B at x-axis to get strain at…

Q: A gas power cycle uses air as the working fluid and has two turbine sections as shown in the figure…

Q: Hot air flows with a mass flow rate m = 0.09 kg/s through an uninsulate of diameter D = 0.15 m,…

A: m˙=.09kg/s D=.15mTi=110oC To=80oCL=5 m…

Q: A solid shaft in a rolling mill transmits 20 kW at 2 revolutions per second. The length of the shaft…

Q: For the frame structure as in the figure, determine the total moment at : MA ,MB, MO

Q: Two designs for a shaft are being considered. Both have an outside diameter of 50 mm and are 600 mm…

Q: Q2/ Use Bisection method to determine the mass of the bungee jumper with drag coefficient (Ca=0.25…

Q: Calculate the thickness and number of leaves of a semi-eluptic carriage spring which is required to…

Q: Question 2 Determine the normal force, shear force, and moment at point C of the beam in Figure 2.

Q: A hollow mast of circular section as shown is to be stiffened by bonding two strips of the same…

A: Find the value of h.

Q: Dtermne the reaction at the supports A and C of Structral Truss shown.

Q: At the instant θ = 45, the athlete is running with a constant speed of 2 m/s. Determine the angular…

Q: Initially saturated water liquid at 200°C is contained in a piston-cylinder. The water is then…

Q: Consider an airflow over the surface of a flat plate with a temperature Ts = 220 °C. At a certain…

A: Ts=220°CTy=T∞-T∞-Tsexp-u∞αFluidyu∞=0.08m/sT∞=220Cαfluid=365E-05m2/sλfluid=0.0329W/mK To-Find:- 1.…

Q: Draw the orthographic views of the following isometric figure. (units in mm

Q: need the answer quickly

Q: If a = 200 mm, t= 20 mm, and G = 77.2 GPa, t 2a t 2a Compute the maximum torque that can be applied…

Q: A steel sleeve of 150 mm outside diameter is to be shrunk on to a solid steel shaft of 100 mm…

Q: Data for two 50-h motors are follows: Alpha Motor Beta Motor Original Cost 37,812 48,247 Annual…

Q: A torsional moment T = 7,005 Nm and a load P = 92,107 N are applied at the same time to a circular…

A: Given data:- Torque = 7005 N-m Force = 92107 N Eccentricity = 6 mm inner diameter = 46mm Outer…

Q: A steam power plant operates on an ideal regenerative Rankine cycle. Steam enters the turbine at 6…

A: Answer: (a) The net work per kilogram of steam flowing through the boiler is 1016.47 kJ/kg. (b) The…

Q: Problem No.4 kg piston in a cylinder with diameter 100 mm is loaded with ng exerts no force on the…

Q: the work metal has a flow curve defined by K=300MPa and n=0.2, and the coefficient of friction…

Q: A single cylinder, four stroke, 3000 cc. petrol engine has a maximum power output of 125 kW at 5500…

A: Given:- Volume of cylinder=3000 cm3,At speed= 5500 rpm,Maximum power output=125 kW,At speed=3000…

Q: 1. Control Unit A steering control unit provides a fully fluid link between the pump and steering…

A: Solution: Given Data:

Q: A piston-cylinder assembly contains ammonia, initially at a temperature of -20°C and a quality of…

A: Answer: (a) The work transfer: W = -73.54 kJ/kg. (b) The heat transfer: Q = 405.47 kJ/kg.

Q: 2.... Hydraulic controlled riveting assembly machine. hydraulic control system. Must include the…

Q: 4-An ideal reheat Rankine cycle operates between the pressure limits of 10 kPa and 8 MPa, with…

A: Answer: The cycle efficiency is 41 percent.

Q: 5. The coefficient of static friction between the flat bed of the truck and the crate it carries as…

Q: QI Define five of the following with sketch. 3- AA2024 4- Rolling 5- Wire drawing 1-Taper turning 2-…

A: Taper turning is a turning technique in which the cutting tool travels at an angle to the…

Q: Q2 A mass-spring system is shown in Figure Q2 with mi = 10 kg, m2 = 20 kg, kı = (10+P) N/m, k2 =…

A: Given data: m1=10 kgm2=20 kgk1=10+P N/mk2=10+Q N/mk3=20+R N/mwhereP=2Q=0R=1 “Since you have posted…

Q: Determine the coordinates of the centroid of the trapezoidal area shown. Assume a = 250 mm, b = 440…

Q: Compute the magnitude of the applied moment M for equilibrium of the system in the current…

A: Consider the free body diagram as shown below for the small roller.

Q: Briefly describe the following types of primary bonding: (a) ionic, (b) covalent, and (c) metallic.…

A: Disclaimer: Since you have posted multiple questions we will solve the first question for you. If…

Q: A steam turbine generator unit consumes 27 MTPH of steam at 1.2 MPa and 325oC where its condensate…

A: INTRODUCTION : In steam power plant, the unorganized form of energy like coal, oil, natural gas get…

Q: The tubular rotor shaft of a wind turbine shown in Figure 3(a) is of 50 mm and 40 mm outer and inner…

A: Find the second moment of area about diametric axis.

Q: A semi-circular vertical plate is partially submerged in the water as shown in the figure. What is…

A: Find the force on the plate due to hydrostatic pressure.

Q: The bending stress at point A.

A: Given data Outer Diameter of Shaft = Do = 50 mm = 0.05 mInner Diameter of Shaft = Di = 40 mm = 0.04…

Q: An iron bar 2.0 cm x 3.0 cm x 10.0 cm at a temperature of 95 °C is dropped into a barrel of water at…

A: The rate at which an exposed body changes temperature through radiation is approximately…

Question

Presents the diagram of the problem, necessary formulas, clearance and numerical solution:

A metal plate 4 mm thick has a temperature difference between its two faces of 32 ◦C. It transmits 200 kcal/h through an area of 5 cm2. Calculate the thermal conductivity of the metal in W/m K.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1.4 To measure thermal conductivity, two similar 1-cm-thick specimens are placed in the apparatus shown in the accompanying sketch. Electric current is supplied to the guard heater, and a wattmeter shows that the power dissipation is 10 W. Thermocouples attached to the warmer and to the cooler surfaces show temperatures of 322 and 300 K, respectively. Calculate the thermal conductivity of the material at the mean temperature in W/m K. Problem 1.4
Repeat Problem 1.35 but assume that instead of surface temperatures, the given temperatures are those of the air on the left and right sides of the wall and that the convection heat transfer coefficients on the left and right surfaces are 6 and 10W/m2K, respectively.
A person wearing a heavy parka is standing in a cold wind. Describe the modes of heat transfer determining heart loss from the person's body.
1.2 The weight of the insulation in a spacecraft may be more important than the space required. Show analytically that the lightest insulation for a plane wall with a specified thermal resistance is the insulation that has the smallest product of density times thermal conductivity.
Find the minimum amount of diameter for the insulation of a spherical water tank? Radius of the tank is 10 m, thermal conductivity is 25 W/(m^2*K) and convective coefficient is 5 W/(m*K)
Presents the diagram of the problem, necessary formulas, clearance and numerical solution: An iron plate 2 cm thick has a cross-sectional area of 5,000 cm2. One of the faces is at 150 ◦C and the other is at 140 ◦C. How much heat flows through the plate each second? For iron, kT = 80 W/m K.
A 1 in. o.d. (outer diameter) tube reactor is insulated with a 3 inch layer of asbestos. If the temperature of the outer surface of the insulation is 100 °F and the rate of heat loss per foot of reactor length is 50 BTU/hr, what must the temperature of the inside of the reactor be? [for asbestos, k = 0.105 BTU/hr ft °F]
For a flat corrugated galvanized steel (conductivity = 26 W/m.K) roof 1/32 in. thick lined with a ¼ in. asbestos-cement (conductivity = 1.2 W/m.K) ceiling 6 inches below the roof, with downward heat flow, calculate the overall thermal transmittance of the roof.
Calculate the thermal resistance of a copper tube with diameter1=0.153 mm diameter2= 0.157 mm and thermal conductivity of 310 W/m.K insulated with a layer of Styrofoam diameter = 0.09 mm
Calculate the heat loss per linear ft from 2 in. nominal pipe (2.375 in. outside diameter)covered with 1 in. of an insulating material having an average thermal conductivity of0.0375 Btu/hr-ft-F. Assume that the inner and outer surface temperatures of the insulationare 380 °F and 80 °F respectively.
HEAT TRANSFER: A thick-walled nuclear coolant pipe (k = 12.5 Btu/hr-ft-°F) with 10 in. inside diameter and 12 in. outside diameter is covered with a 3 in. layer of asbestos insulation (k 0.14 = Btu/hr-ft-°F). If the inside wall temperature of the pipe is maintained at 550°F, (a) calculate the heat loss per foot of length. The outside temperature is 100°F. (b) Find the interface temperature between the pipe and the insulation.
6. Air flows at 120 o C in a thin-walled tube (k = 18 W/m o C) with h = 65 w/m 2 - o C. The inside diameter of the tube is 2.5 cm tand the thickness is 0.4 mm. The tube is exposed to an environment with h = 6.5 W/m 2 - o C and temperature of 15 o C. Calculate the the heat loss for 1 m length. What thickness of insulation having k = 40 W/m- 0 C should be added to reduce heat loss by 90 %.