Problem 1: Determine the flexural strength of a W 410 x 67 beam with a simple span of 8 m and Fy = 250 MPa subject to the following conditions. 1. Lateral bracing are provided at 1.6 m interval along the span. 2. Lateral bracing is provided only at midspan. 3. No lateral bracing is provided. Properties of W 410 x 67 A = 8,580 mm² d = 409 mm bf = 179 mm tf = 14.4 mm tw = 8.76 mm Ix = 244 x 106 mm4 1,190 x 10³ mm³ Sx rx = 169 mm ly=13.7 x 106 mm4 Sy = 153 x 10³ mm³ ry = 39.9 mm J = 1.05 x 106 mmª Zx = 1,348 x 10³ mm³ Cb = 1.30

Problem 1: Determine the flexural strength of a W 410 x 67 beam with a simple span of 8 m and Fy = 250 MPa subject to the following conditions. 1. Lateral bracing are provided at 1.6 m interval along the span. 2. Lateral bracing is provided only at midspan. 3. No lateral bracing is provided. Properties of W 410 x 67 A = 8,580 mm² d = 409 mm bf = 179 mm tf = 14.4 mm tw = 8.76 mm Ix = 244 x 106 mm4 1,190 x 10³ mm³ Sx rx = 169 mm ly=13.7 x 106 mm4 Sy = 153 x 10³ mm³ ry = 39.9 mm J = 1.05 x 106 mmª Zx = 1,348 x 10³ mm³ Cb = 1.30

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A prismatic beam having 250 mm x 500 mm is reinforced for flexure at the bottom with 5-ϕ20 mm with an effective depth of 380 mm. It is simply supported over a clear span of 5.5 m and designed to support a total factored uniformly distributed load of 32 kN/m over the entire span. Concrete weighs 24 kN/m3, Concrete strength f’c = 21 MPa and rebar strength fy = 280 MPa. Determine the factored shear force at the critical section, distance "d" from the face of support . Determine the nominal concrete shear strenght in kN as per NSCP 2015. Determine the required spacing in mm of 10-mm-dia. stirrups within the critical region of the beam.
Compute the required section modulus Z of a steel beam 5.0 m between simple supports and will carrying 11 cm thick and 100 cm concrete wall weighing 30 kN/m³. Allowable bending stress is 200 MPa and the beam itself weighs 0.5 kN/m.
A prismatic beam having 275 mm x 500 mm is reinforced for flexure at the bottom with 5-ϕ20 mm with an effective depth of 420 mm. It is simply supported over a clear span of 6 m and designed to support a total factored uniformly distributed load of 35 kN/m over the entire span. Concrete weighs 24 kN/m3, Concrete strength f’c = 21 MPa and rebar strength fy = 280 MPa. Determine the required nominal shear force the stirrups must sustain based on the critical shear force at a section located distance "d" from face of support. A. 15.3 B. 28.4 C. 24.2 D. 32.2
A prismatic beam having 250 mm x 500 mm is reinforced for flexure at the bottom with 5-ϕ20 mm with an effective depth of 420 mm. It is simply supported over a clear span of 6 m and designed to support a total factored uniformly distributed load of 32 kN/m over the entire span. Concrete weighs 24 kN/m3, Concrete strength f’c = 21 MPa and rebar strength fy = 280 MPa. 1. Determine the factored shear force at the critical section, distance "d" from the face of support . (A to D) 2. Determine the nominal concrete shear strenght in kN as per NSCP 2015. (E to H) 3. Determine the required spacing in mm of 10-mm-dia. stirrups within the critical region of the beam. (I to L) Correct Answers: A. 82.5 F. 80.2 I. 200
A prismatic beam having 28 mm x 40 mm is reinforced for flexure at thebottom with 3-φ16 mm with an effective depth of 420 mm. It is simplysupported over a clear span of 6 m and designed to support a total factoreduniformly distributed load of 28 kN/m over the entire span. Concrete weighs 21 kN/m3, Concrete strength f’c = 21 MPa and rebar strength fy = 280MPa.1. Determine the factored shear force (kN) at the critical section for shear located a distance"d" from the face of support .
Given that a simple span beam has concentrated load of 50KN acting at midspan and that the allowable shear stress of the material is 1 48MPa determine the computed depth of the span of the beam is 4 m and the width is 100mm
If the given beam section is used for a simply supported beam 5.0 m span, using f’c = 21 MPa and fyt = 280 MPa: Calculate the nominal shear strength of the stirrups, Vs = kN
A reinforced concrete beam has a simple span of 4.5 m and carries a dead load of 20 kN/m and live load of 35 kN/m. Steel covering is 75 mm. Using f’c = 28 MPa and fy = 415 MPa.(a) Determine the maximum moment due to the factored loads.(b) Determine the least dimensions of the beam using the maximum allowable reinforcement ratio(c) Determine the maximum area of steel.
A doubly reinforced beam, which have a base of 310 mm, and an effective depth of 410 mm, is reinforced with steel area of 2263 sq. mm at the bottom, and 1232 sq. mm on the top. Take d' = 70 mm, fc' = 21 MPa, and fy = 345 MPa. c) What is the value of ρbalance?
A reinforced concrete beam has a simple span of 4.5 m and carries a dead load of 20 kN/m and live load of 35 kN/m. Steel covering is 75 mm. Using f’c= 28 MPa and fy = 415 MPa. Determine the maximum moment due to the factored loads. Determine the least dimensions of the beam using the maximum allowable reinforcement ratio Determine the maximum area of steel.
A square, tied column 370 mm wide is reinforced with 4 25-mm-diameter vertical bars with fy = 420 MPa enclosed in 10-mm-dia. ties. Using f'c = 24 MPa, calculate the nominal axial strength at balanced condition in kN with bending about the x axis.
A built-up shape consisting of two 20 mm × 450 mm flanges and a 20 mm × 1300 mm webis used as a beam. If Fy = 400 MPa, what is the nominal flexural strength based on flange local buckling?