Problem 1. The joint is subjected to a force of 250 lb as shown. The member has a rectangular cross section of width 0.5 in. and thickness 0.75 in. a) Sketch the normal-stress distribution acting over section a-a. b) Determine the position of the Neutral Axis relative to the Centroidal Axis. c) Determine the state of stress at points A and B, include both combined normal stress and shear stress, and sketch the results on differential elements located at these points. Give special attention to the plane the stress components act and the directions.

Problem 1. The joint is subjected to a force of 250 lb as shown. The member has a rectangular cross section of width 0.5 in. and thickness 0.75 in. a) Sketch the normal-stress distribution acting over section a-a. b) Determine the position of the Neutral Axis relative to the Centroidal Axis. c) Determine the state of stress at points A and B, include both combined normal stress and shear stress, and sketch the results on differential elements located at these points. Give special attention to the plane the stress components act and the directions.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 30 mm. The outer diamter and thickness of the pressure vessel is 500 mm and 10 mm. Its length is 2m. Determine the maximum internal pressure (MPa) that can be applied if the longitudinal stress is limited to 155 MPa, and the circumferencial stress is limited to 55 MPa.
1) Determine the principal stresses. 2) Specify the orientation of the element
Two fork-end pieces are to be joined together by a single steel pin of 25 mm diameter and they arerequired to transmit 50 kN. Determine the minimum cross-sectional area of material required in one branch of eitherfork if the stress in the fork material is not to exceed 180 MN/m2. What will be the maximum shear stress in the pin?1.39 x 10 m*; 50.9 MN/m*]
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. Draw appropriate FBDs showing how the internal forces were determined. A square bar (side length = 50 mm) is welded to a fixed supporting slab. A 30-mm diameter pin is inserted in the bar. When the loading shown is applied, determine the following: a. maximum normal stress in the bar (MPa) and bearing stress between the pin and the bar (MPa)b. stress in the weld between the bar and the supporting slab (MPa)c. shear stress in the pin (MPa) and shear stress in the bar (MPa)
Problem 2A set of stresses applied on the 50-mm x 50-mm ABCD plate cause the plate to deform as shownwhere both sides AC and D'B' remain horizontal. a) Find the average axial strain of side AC, AD and BC of the plate b) Find the shearing strain at each of the corners A,B,C and D
A body is subjected to a direct tensile stress of 300 MPa in one plane accompained by a simple shear stress of 200 MPa. Determine maximum normal stress on the plane.
A thin walled spherical shell is subjected to an internal pressure. If the radius of the shell is increased by 1% and the thickness is reduced by 1%, with the internal pressure remaining the same, the percentage change in the circumferential (hoop) stress is.....
The cross-sectional area of the bar ABCD is 600 mm². Determine the maximum normal stress in the bar?
A cylindrical pressure tank is fabricated by butt-welding 19 mm-thick plate with spiral seam shown below. The pressure in the tank is 2.76 MPa, and an axial load of 133.5 KN is applied to the end of the tank through a rigid bearing plate. Determine the normal stress and shearing stress perpendicular to the weld.
The connection consists of a plate connected to another plate by four 22 mm diameter rivets. It carries a load P = 60 kN at a distance of 344 mm from the centroid of the rivet group. Assume a = 165 mm Determine the shear stress on each rivet due to force alone, in MPa. Determine the shear stress on each rivet due to torsion alone, in MPa. Determine the shear stress on the highly stressed rivet, in MPa
The rectangular bar is connected to the support bracket with a 17-mm-diameter pin. The bar width is w = 70 mm and the bar thickness is 20 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 130 MPa, the bearing stress in the bar cannot exceed 140 MPa, and the bearing stress in the bracket cannot exceed 150 MPa. Determine the maximum value of Pmax that can be supported by the structure.
The tensile member shown, 50 mm x 75 mm in cross section is subjected to a load P. The plane A-A makes an angle 15° with the x-axis. a. Determine load P when the tensile stress at section A-A is 80 MPa. b. Determine the shear stress on section A-A. c. At what angle of plane A-A is the shear stress equal to 27.35 MPa?