PROBLEM 10 How much weight is going to each of Sam's arms, assuming Sam is in equilibrium (aka everything is stable, as in Sam is not falling). 45lb plate on the left side and a 10 lb plate on the right. Assume the bar is weightless (ask me what you would do if it wasn't weightless which is more realistic) 8 FT Sam 1 FT 3 FT A'Weightlifter Supporting an Asynimetrically-loaded Barbell DRAW FREE BODY DIAGRAM HERE WITH ALL REACTIONS, FORCES, AND DIMENSIONS LABELED Pag

PROBLEM 10 How much weight is going to each of Sam's arms, assuming Sam is in equilibrium (aka everything is stable, as in Sam is not falling). 45lb plate on the left side and a 10 lb plate on the right. Assume the bar is weightless (ask me what you would do if it wasn't weightless which is more realistic) 8 FT Sam 1 FT 3 FT A'Weightlifter Supporting an Asynimetrically-loaded Barbell DRAW FREE BODY DIAGRAM HERE WITH ALL REACTIONS, FORCES, AND DIMENSIONS LABELED Pag

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 50-m steel tape is of standard lengthunder a pull of 5.5kg when supportedthroughout its entire length. The tape weighs0.05 kg/m, has a cross-sectional area of 0.04sq.cm., and being made of steel, its modulusof elasticity is 2.10x106 kg/cm2. This tapewas used in the field to measure a distancethat was determined to be 458.650m. At thetime the measurement was made, theconstant pull applied was 8kg with the tapesupported only at its end points. Determinethe correct length of the line.
A rectuangular wooden beam ( fb = 7.0 MPa, E = 12.9 GPa) ha s across-sectional area of300 mm by 600 mm. The beam has a simple span of five meters. A vibrating machine weighing800 kg is located at the midspan. The machine is working under a constant force of 500 N andaccidentally stopped after 0.7 sec (rectangular pulse). Determine the following:Stiffness, ? = _____________________Angular natural frequency, ?? = _________________ Displacement at t = 0.7 seconds ?(? = 0.7) = _______________________Displacement at t = 1.5 seconds ?(? = 1.5) = _______________________(???)? = _______________
Engineering Mechanics (Like/Thumbs-up will be given. Write the solutions&FBD legibly. Include negative sign if in Compression, ex. -1,500 or if in Tension, ex. 1,500. Round to the nearest whole number.) The bucket and its load have a combined weight of 4000 lb with center of gravity at G. You may neglect the effect of the weights of the other members. Determine: A. Force in the hydraulic cylinder AB, in lb B. Magnitude of the pin reaction at O, in lb round off to two (2) decimal places
The weights of two children sitting at ends A and B of a seesaw are 84 lb and 64 lb, respectively. Where should a third child sit so that the resultant of the weights of the three children will pass through C if she weighs (a) 60 lb, (b) 52 lb.
the weight of the file cabinet is 60 lbs and G represents its center of gravity the coeffiecent of friction between the cabinet and the floor is 0.3 determine the minimum horizontal force P required to cause the cabinet to..... a) slide across the floor b) to tip over c) if the force p equals 12 what happens?
a pottery manufacturer has an order to manufacture 5000 hanging vases to hold ½ pt. of water when full. The vases are designed so as to fit into the corner of a room. The faces of each vase are triangular in shape and intersect to form a pointed bottom. The area of the polygon cut out of the plane of the base by the lateral faces is 3sq.in. The height of the vase is 8 in. Compute the weight of pottery required if pottery weighs 130lb. per cu.ft.
28. Situation 10 - An object (SG = 7.3) floats in mercury (SG = 13.6) such that a certain portion is above the liquid surface. a. What fraction of the volume of the object floats above the surface of the mercury? Round off to three decimal places. b. If the volume of the object below the liquid surface is 0.014 m3, what load, in kN, applied vertically that would cause the object to be fully submerged? Round off to two decimal places. c. If the volume of the object below the liquid surface is 0.014 m3, what is the weight, in kN, of the object? Round off to two decimal places.
Replace the five forces acting on the plate by a wrench. Suppose that F1 = 700 N and F2 = 550 N . (Figure 1) Part A Determine the magnitude of the force of the wrench. Express your answer to three significant figures and include the appropriate units. Part B Determine the couple moment of the wrench. Express your answer to three significant figures and include the appropriate units. Enter positive value if the sense of direction of the couple moment is the same as that of the resultant force and negative value if the sense of direction of the couple moment is opposite to that of the resultant force. Part C Determine the point P(x,z) where the wrench intersects the x-z plane. Enter the x and z coordinates of point PP separated by a comma using three significant figures.
Q2/ You want to move a 400-N crate across a level floor by pulling upward on the rope at an angle of 30° above the horizontal. How hard must you pull to keep it moving with an acceleration of a = 0.5 m/s² ? Assume that µ = 0.30.
Optimum Mechanics Co. lifted a car weighing 3184 lbf using the system presented. The platform was supported by four (4) cables (Cable AB, AC, AD, and AE). Determine the following: (Take AB = AE). note: Express your answer in units.Observe 3 decimal places.The error threshold is ± 2.50% Relative to the right answer. A: < 0 0 10.143 >ft B: < 4.954 4.997 0 > ft C: < 6.66 -4.997 0 > ft D: < -7.029 -4.534 0 > ft E: < -5.439 4.997 0 > ft 1.) Determine the x-component of the Tension in AC. 2.) Determine the y-component of the Tension in AC. 3.) Determine the z-component of the Tension in AC.
Optimum Mechanics Co. lifted a car weighing 3184 lbf using the system presented. The platform was supported by four (4) cables (Cable AB, AC, AD, and AE). Determine the following: (Take AB = AE). note: Express your answer in units.Observe 3 decimal places.The error threshold is ± 2.50% Relative to the right answer. A: < 0 0 10.143 >ft B: < 4.954 4.997 0 > ft C: < 6.66 -4.997 0 > ft D: < -7.029 -4.534 0 > ft E: < -5.439 4.997 0 > ft 1.) Determine the TENSION IN CABLE AE.
Let G = 100kg, calculate the unknown loads A and B in order for the whole mechanism to stay stationary