If a verical Force of 2.5kN is applied to the hook at A determine the tension in each of the three cables for equilibrium. Set d = 1m. Problem 4If a vertical force of 2.5 kN is applied to the hook at A, determine the tension ineach of the three cables for equilibrium. Set d = 1 m.B3 mF=2.5 KN3 mm0.75 my

Answered: Image /qna-images/answer/899e2fee-7e14-4d35-8dba-e0a98ed02f8b.jpg

Answered: Problem 4 If a vertical force of 2.5 kN…

Problem 4 If a vertical force of 2.5 kN is applied to the hook at A, determine the tension in each of the three cables for equilibrium. Set d = 1 m. 3 m 1.5 m F=2.5 KN 3m 0.75 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Analysis of Internal Forces of Statically Determinate Beams Objective: To determine the internal…

Q: Determine the value of El y at the right end of the overhanging beam. a = 4.4 m, b = 2.8 m, Wo =…

Q: Draw the shear and moment diagram of the beam shown. 8 KN 16 KN C B FILT 3 m 3m + 1. Determine the…

Q: This is a mechanics of deformable bodies problem

A: Given, t = 20 mm p = 12 MPa

Q: In natural state, a soil weighs 3500 lb/cy. The same soil has a load factor of 0.83. a. What is the…

Q: View Policies Current Attempt in Progress The turbine shown in the figure below develops 100 hp when…

A: Determine (a) the elevation h, (b) the pressure difference across the turbine, (c) the flowrate…

Q: Question 7 Listen Moisture content specimens should be discarded after testing and not used in any…

A: 1. True. Moisture content specimen should be discarded after testing and should not be used in…

Q: Current Attempt in Progress Water flows steadily from a nozzle into a large tank as shown in the…

Q: Use the portal method and determine (approximately) the reactions at supports A and B. YKN X KN E A…

Q: Determine the value of El y at the right end of the overhanging bea

Q: Determine the reactions and the force in each member of the space truss. Indicate if the members are…

Q: As shown in the figure, a rigid beam with negligible weight is pinned at one end and attached to two…

Q: Water flows steadily from a nozzle into a large tank as shown in the figure below. The water then…

Q: From the field notes of a closed traverse shown for the linear error of closure and relative error.…

A: Given: STATION DISTANCE (m) AZIMUTH AB 233.10 122° 30' BC 242.05 85° 15' CD 191.50 20° 00'…

Q: 20. What are the cross sectional area, leg dimensions and thickness of an L6x4x1/2? (Hint: Use your…

A: AISC is the american standard code for the design of steel construction.

Q: Q5: Design the diameter of a steel pipe to carry water having kinematic viscosity v=10 m²/s with a…

Q: A small shop in Bulacan fabricates threshers for palay producers in the locality. The shop can…

A: GIVEN- Labor cost per unit = P1800 Material cost per unit= P2500…

Q: Messages 7. A 4.0 M simply supported beam carries a uniform distributed load of 2KN/M over its…

A: Design the section of beam Consider timber beam

Q: 2. Given H = 1.8 m & D = 0.2 m through the hole in the open top container. Determine the head losses…

A: GIVEN :- Head , H = 1.8 m Diameter of hole, D = 0.2 m Exit discharge, Q = 0.163 m3/s To Determine :-…

Q: F3-5. Determine the force in each member of the truss and state whether it is in tension or…

A: Given : The force in each member of truss ?

Q: Question: A 12 mm thick plate is connected to two 8 mm thick plates, on either side through a 16 mm…

A: Given- Thickness of plate T=12 mm, Dia of rivet=16 mm, Permissible bearing stress p=270 MPa, It is…

Q: er a simply supported beam of length / subjected to a 1/ y(x) = P x ≤ 1/2, the deflection is given…

Q: A block of wood with length "h" and cross-sectional area "A" is submerged in water with 50 mm…

A: KINDLY NOTE: As per Bartleby guidelines, we are supposed to solve the first question in case…

Q: A certain firm has the capacity to produce 650,000 units of product per year. At present, it is…

A: Capacity to produce = 650000 units The actual unit produced, x = 62100×650000 = 403000 units Annual…

Q: A company which manufactures electric motors has a production capacity of 200 motors per month. The…

Q: Water is to be moved from one large reservoir to another at a higher elevation as indicated in the…

Q: The state of plane stress at a point is represented on the element shown in the figure. The element…

Q: Find the C, and the "apparent" OCR for a superficial clay stratum that is 4m thick. The water is at…

Q: Determine the force in each member of the loaded truss. Make use of symmetry of the truss and of the…

Q: Q4: A rapid filter plant is to treat 28000 m³/d at a rate of 110 m/d. Determine the size and number…

Q: Situation #4 Determine the force in each member of the truss 60⁰ B, -Am -Am- Am 60 16. What is the…

A: Find out the support reactions and all member forces in the given truss. Use equilibrium conditions…

Q: Use the portal method and determine (approximately) the reactions at supports A and B. YKN XkN- 5m B…

Q: A force Pacts on the frame shown at point E. Knowing that the absolute value of the moment of Pabout…

A: Determine the magnitude of the force P.

Q: A factory engaged in the fabrication of an automobile part with a production capacity of 700,000…

A: When the revenue generated from a business activity exceeds the expenses, costs, and taxes involved…

Q: A pump is to move water from a lake into a large, pressurized tank as shown in the figure below at a…

Q: Why friction loss test is conducted in impact test experiment?

A: An impact test is a test conducted to determine the amount of energy lost when the fracture of…

Q: A Civil Engineer produces a certain construction material at a labor cost of P16.20 per piece,…

Q: The following results were obtained from sieve analysis and Atterberg limits of the Soils.…

A: Given: Liquid limit (LL)=23% Plastic limit(PL)=8% Percentage of material retained in sieve no. 200…

Q: HYDROSTATIC FORCE ON PLANE SURFACES I need help analyzing my experiment. For a Fully Submerged…

A: Data given

Q: A wastewater treatment plant discharges 2.16x107 L/hr of treated effluent with an ultimate BOD of…

A: Given:Waste water discharge in the riverQw=2.16×107 LhrQw=2.16×107×10-360×60Qw=6 m3sUltimate BOD of…

Q: 2. Determine the forces in member BC, BE and EF of the truss shown in the figure by Method of…

A: Using section method

Q: Determine the force in each member of the space truss and state if the members are in tension or…

Q: Give an example of a geometric sequence. What is the first term? What is the common ration? What is…

A: This question comes from surveying and mechanics Asked for some information about Geometric…

Q: Q1: A canal of trapezoidal section has bed width of 8 m and bed slope of 1 in 4000. If the depth of…

Q: A moment magnitude of 4.8 produced a rupture length of 1550km and rupture width of 320km. Determine…

A: Given data : Moment Magnitude = 4.8 , Rupture length L = 1550000m , Rupture width W = 320000 m Find…

Q: 4. For the next section of river parameters, how deep would the river need to be in order for the…

A: Objective: To determine the depth of river for the given flow to be turbulent. Given: Flow…

Q: 38. What grade of steel is preferred for the fabrication of most structural shapes other than…

A: Given data : Structural shapes Find : Grade of steel and its yield and tensile stress Shapes like W…

Q: Solve the given beam below, determine the maximum moment L1 = 65 kN L2 = 74 KN L1 KN A 1m 3 m L2 KN…

Q: Euler-Cauch equation is used to solve *

A: This question comes from Fluid mechanics. Here asked for use of the Eular Cauchy equation

Q: 35. What grade of steel is most commonly used today in the production of W-shapes, and what are its…

Concept explainers

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.

Question

If a verical Force of 2.5kN is applied to the hook at A determine the tension in each of the three cables for equilibrium. Set d = 1m.

Problem 4
If a vertical force of 2.5 kN is applied to the hook at A, determine the tension in
each of the three cables for equilibrium. Set d = 1 m.
B
3 m
F=2.5 KN
3 m
m
0.75 m
y

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the beam and loading shown below (L = 2.4 m, E = 200 GPa, I = 1000 mm4 and w = 30 kN/m), find (a) TThe slope at point D.(b) The reaction force at end A
Compute the vertical components of the hinge forces at C as they act upon member AC in kN P= 89 kN and x= 3.7 m. Write numerical value only and in 2 decimal places
If P = 26 and M = 5.74, Determine the Axial Force at point B of the Beam shown.
Calculate the shear at right end of span BC in kN.0
If M = 6.23 and w = 17.2, Determine the Shear Force at point B of the Beam shown.
Calculate the moment of force of 1.4 kN with respect to points P1 and P2.
Set P=0.6 kN and w=1.20 kN/m. Consider A is a roller support and B is a pin support. Illustrate the shear and moment diagram of the beam below.
determine the moment (m-kN) about point A due to the 3 kN and the two 17 kN forces.
What is the Maximum moment in kN-m. Given: w = 45, a = 3, b = 3, and c = 2.
per the attached figure: a shear force of V = 448 kN is applied to the box girder. determine the shear flow at points C and D.
If the beam is subjected to an internal moment of M = 40 kN . m, determine theresultant force caused by the bending stress distribution acting on the top flange A.
Calculate the vertical force reaction at left support of the beam in kN.