Problem #5: For the 2D beam below, with F, = 15 kips, M, =7 kip-ft, and shear and bending moment diagrams. Report your answer in kip and kip-ft to one decimal place. Wo 2.5 kip/ft draw the F. 0. Wo F, Mo Mo, 2.0 ft 1.0 ft 5.0 ft 2.0 ft By uploading this work, I attest that the work contained herein is solely my own, that I only used the given equation sheet as a reference, and that I have not received any information from anyone else or source regarding this exam at any time.

Problem #5: For the 2D beam below, with F, = 15 kips, M, =7 kip-ft, and shear and bending moment diagrams. Report your answer in kip and kip-ft to one decimal place. Wo 2.5 kip/ft draw the F. 0. Wo F, Mo Mo, 2.0 ft 1.0 ft 5.0 ft 2.0 ft By uploading this work, I attest that the work contained herein is solely my own, that I only used the given equation sheet as a reference, and that I have not received any information from anyone else or source regarding this exam at any time.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.42P: For the beam AB shown in Cases 1 and 2, derive and plot expressions for the shear force and bending...

See similar textbooks

Similar questions

A two-axle carriage that is part of an over head traveling crane in a testing laboratory moves slowly across a simple beam AB (sec figure). The load transmitted to the beam from the front axle is 2200 lb and from the rear axle is 3800 lb. The weight of the beam itself may be disregarded. Determine the minimum required section modulus S for the beam if the allowable bending stress is 17,0 ksi, the length of the beam is 18 ft, and the wheelbase of the carriage is 5 ft. Select the most economical I-beam (S shape) from Table F-2(a), Appendix F.
Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction provided by the ground to be uniformly distributed. Let a = 5.0 ft, b = 3.4 ft, P = 25 kips, and w = 1.1 kips/ft. Label all significant points on each diagram. Determine the maximum value of (a) the internal shear force and (b) the internal bending moment.Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
Use the graphical method to construct the shearforceand bending-moment diagrams for the beams shown in Figurebelow . Label all significant points on each diagram, andidentify the maximum moments along with their respective locations.Clearly differentiate straight-line and curved portions of thediagrams.
The cantilever beam in Fig. (a) carries a triangular load, the intensity of which varies from zero at the left end to 360 lb/ft at the right end. In addition, a 1000-lb upward vertical load acts at the free end of the beam. (1) Derive the shear force and bending moment equations, and (2) draw the shear force and bending moment diagrams. Neglect the weight of the beam
A simply supported beam, 50mm wide by 100mm high and 300 mm long is subjected to a concentrated load of 3000 N at a point 100 mm from one of the supports. Draw the shear force and bending moment diagrams for the beam.
Draw the shear force and bending moment diagrams of the given simple headstock beam? can you solve it step by step!
c) The same rectangular cross-section beam in Q2b is subjected to a maximum bending moment of 25,000 Nm and experiences sagging. Assuming that the centroidal axis passes through the beam section at (d/2), calculate the maximum bending stress (?max) the beam will experience. Give your answer in N/mm2 and to 2 decimal places.
A gantry crane of weight W=100 Kg moves across a bridge with the length /=5 m. The front axle of the crane (which is nearer end A) carries 3/4W whereas the rear axle (nearer end B) carries 1/4 W. The distance of the axles is b = 1/20. Determine the maximum value of the bending moment and enter your answer in N-m units.. Remember to also show all your work (FBDs, calculation steps, etc on the handworked file) HINT: Determine the shear and bending moment equations along the beam. Assume only concentrated loads at the front and rear axles. So it’s wrong answer 1136 N can anyone how to solve for it different ?
6.. A cantilever beam is 2.5 m long, and carries a concentrated load of 380 N at its midpoint, and a uniformly distributed load of 400 N/m over a span from its free end to a point 0.5 m from the free end. Neglecting the mass of the beam itself, draw the shear force and bending moment diagrams for the beam. Show all calculations as well
SHOW YOUR SOLUTIONS PLS, INSTRUCTIONS: For the beam shown, (1) derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) (2) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Specify the values for key points on the diagrams. Let a=7.0 ft, b=8.7 ft, wa=13 kips/ft, and wb=7 kips/ft. QUESTIONS: 4) With reference to problem 1, what is the bending moment (in kip-ft rounded to the nearest whole number) at x = 9.0 ft? 5) With reference to problem 1, what is the maximum bending moment? Express your answer in kip-ft rounded to three significant figures.
When a beam has only uniformly distributed forces applied, the moment diagram consists of piecewise (answer) forces.
Draw complete shear and bending moment diagrams. Showordinates at key points and indicate magnitude of shear andmoment. Neglect the beam weight.