Problem 7.5 For the following voltage and current phasors, calculate the complex power, apparent power, real power, and reactive power. Specify whether the pf is leading or lagging. (a) V = 220/30° V ms, I = 0.5/60° A ms (b) V = 250/-10° V rms, I = 6.2/-25° A ms (c) V = 120/0° V rms, I = 2.4/-15° A rms (d) V 160/45° V ms, I 8.5/90° A ms %3D

Problem 7.5 For the following voltage and current phasors, calculate the complex power, apparent power, real power, and reactive power. Specify whether the pf is leading or lagging. (a) V = 220/30° V ms, I = 0.5/60° A ms (b) V = 250/-10° V rms, I = 6.2/-25° A ms (c) V = 120/0° V rms, I = 2.4/-15° A rms (d) V 160/45° V ms, I 8.5/90° A ms %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Discuss why a. Complex power in an AC circuit is more than the DC resistance. b. Receiving end voltage of an unloaded long line may be more than sending end voltage. c. Inductance of the three phase of a transmission line are generally not equal. d. It is necessary to use the geometric means radius in the formula for the inductance calculation whereas the formula for the capacitance calculation uses the actual radius.
A lightning strikes a 30-m unshielded over-head transmission line tower Which has the following parameters Surge impedance of the tower= 100ohms Surge impedance of lightning channel at tower top =500ohms Tower-footing resistance=10ohms Tower height =30 m Cross-arm height=27m The lightning strike current is assumed to be a constant 30 kA for a duration of 20 µs. The raveling wave propagation speed in the tower is 1.2* 108 m/s. i) Determine the voltage reflection coefficients at tower top and tower foot. ii) Ignoring the phase voltage, determine the insulator voltage after 2µs.
A lightning strikes a 30-m unshielded over-head transmission line tower Which has the following parameters Surge impedance of the tower= 100ohms Surge impedance of lightning channel at tower top =500ohms Tower-footing resistance=10ohms Tower height =30 m Cross-arm height=27m The lightning strike current is assumed to be a constant 30 kA for a duration of 20 µs. The raveling wave propagation speed in the tower is 1.2* 108 m/s. i) Determine the voltage reflection coefficients at tower top and tower foot. ii) Determine the time of travel from tower top to tower foot. iii) Determine the time of travel from cross arm to tower foot. iv) Draw the voltage lattice diagram with proper labels of the time. v) Ignoring the phase voltage, determine the insulator voltage after 2µs. b) The insulator voltage approaches a constant value after 2 µs. If the basic impulse insulation level (BlL) of the insulator for phase conductor is 150 kV, evaluate the condition of the…
A lightning strikes a 30-m unshielded over-head transmission line tower Which has the following parameters Surge impedance of the tower= 100ohms Surge impedance of lightning channel at tower top =500ohms Tower-footing resistance=10ohms Tower height =30 m Cross-arm height=27m The lightning strike current is assumed to be a constant 30 kA for a duration of 20 µs. The traveling wave propagation speed in the tower is 1.2* 108 m/s. a)draw the voltage lattice diagram with proper labels of the time b) ignoring the phase voltage, determine the insulator voltage after 2µs. c) The insulator voltage approaches a constant value after 2 µs. If the basic impulse insulation level (BlL) of the insulator for phase conductor is 150 kV, evaluate the condition of the insulator and conclude the type of power quality problem that will occur for an end-user facility connected to the transmission line. Assume that the surge arresters and circuit breakers at the end-User facility are working properly.
7. Assuming no transients are present, calculate the power absorbed by each element shown below at t = 0, 10, and 20ms. Please show full calculations.
AC electrical circuit is below: (refer picture below) a. Determine the current flowing in the load. b. If it is desired that the system power factor be 0.9. With system frequency = 50 Hz. Determine how large the capacitor is must be installed? Which one is correct? A/B/others answer A. C = 7.7015 mF B. C = 35.243 µF c. Please Draw all the phasor. Please give complete, details, and correct answer. Please do step by step, draw the phasor Please using handwriting (not typing ). THANK YOU, I WILL GIVE MANY THUMBS UP.
Can someone help me try to understand the effect of Capacitance Multiplier Design Parameters on Power Supply Noise Reduction? Please also provide mathematical equation and make it computerized so I can unnderstand it better. PLEASE JUST REJECT IT IF YOU CAN'T HELP ME. THANKS!
For the circuit shown in Figure 7.4, determine apparent power S, real power P, reactive power Qand power factor PF. Also, draw the power triangle. The source is 120 volts.
Given the system below, find the sinusoidal expression for the unknown current ?1 if i? = 30 × 10−6 sin(?? + 80°) and ?2 = 4 × 10−6 sin(?? − 50°).
Derive and analyse relation of capacitance for 3 core cables.
The capacitance per kilometre of a 3-phase belted cable is 0.18 µF between two cores with the third core connected to sheath. Calculate the kVA taken by 20 km long cable when connected to 3-phase. 50 Hz, 3300 V supply.
In the circuit given belowX=7andY=5Ωas they are defined as;Vvoltage phasoramplitudehow many volts?NOTE: Please enter your answers as 2 digits after the comma.