Problem:1 The following is the system data for a load flow solution. Determine the bus voltages at the end of first iteration using Gauss-Seidel method : Take a = 1.6. The line admittances: Bus code Admittance 1-2 2-j8.0 1-3 1-j4.0 2-3 0.666-j 2.664 24 1-j4.0 3-4 2-j8.0 The schedule of active and reactive powers: Bus code P V Remarks 1 1.06 Slack 1+ j0.0 1+ j0.0 1+ j0.0 2 0.5 0.2 PQ 0.3 PQ PQ 3 0.4 4 0.3 0.1

Problem:1 The following is the system data for a load flow solution. Determine the bus voltages at the end of first iteration using Gauss-Seidel method : Take a = 1.6. The line admittances: Bus code Admittance 1-2 2-j8.0 1-3 1-j4.0 2-3 0.666-j 2.664 24 1-j4.0 3-4 2-j8.0 The schedule of active and reactive powers: Bus code P V Remarks 1 1.06 Slack 1+ j0.0 1+ j0.0 1+ j0.0 2 0.5 0.2 PQ 0.3 PQ PQ 3 0.4 4 0.3 0.1

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.32P

See similar textbooks

Similar questions

The figure below shows the one-line diagram of a simple three-bus power system withgeneration at bus 1. The voltage at bus 1 is V1 = 1.0∠0°per unit. The scheduledloads on buses 2 and 3 are marked on the diagram. Line impedances are marked inper unit on a 100 MVA base.(a) Using Gauss-Seidel method and initial estimates of ?2(0) = 1.0 + ?0, ?3(0) = 1.0 + ?0, determine V2and V3. Perform two iterations.(b) If after several iterations the bus voltages converge to?2 = 0.90 − ?0.10 pu?3 = 0.95 − ?0.05 pudetermine the line flows and line losses and the slack bus real and reactive power.
Figure 5 shows a single-line diagram of a three-bus power system. Power flow input data are givenin Tables 1 and 2. (a) Determine the Ybus Matrix (b) Use Gauss-Seidel method to compute V2(1) and V3(1), the phase voltages at bus 2 and 3 after the first iteration. Use zero initial phase angles and 1.0 per-unit initial bus voltage magnitudes.
Draw the phasor diagrams for a transmission line (modeled as short transmission line) when supplying a leading, lagging and unity power factor loads. Phasor diagram should include sending end voltage, receiving end voltage, load power factor, and line current. Based on the phasors answer the following: a. For lagging power factor load, is |??| >|??|? True/Falseb. For leading power factor load, is |??| >|??|? True/Falsec. For unity power factor load, is |??| >|??|? True/False
For the system in Figure 4 with given generation and load dispatch determine the voltages after two itterations of Gauss-Seidel method. Assume the initial voltage to be 1.01 at angle of 0◦ pu at bus 1, 1.015 at angle of 0◦ pu at bus 2, and 1.0 at angle of 0◦ pu at bus 3. All line impedances are in per unit on a common base, and charging is neglected. Take base power of 100 MVA.
A single-line diagram of a four-bus system is shown in fiugre. Equipment ratings and per-unit reactances are given as follows.Machines 1 and 2: 100 MVA 20 kV; X1= X2 = 0.2; X0= 0.04 Xn= 0.05 Transformers T1 and T2: 100 MVA 20Y/345Y kV; X1 = X2 = X0 = 0.08. On a base of 100 MVA and 345 kV in the zone of the transmission line, the series reactances of the transmission line are X1 = X2 = 0.15 and X0=0.5 per unit. (a) Determine the bus impedance matrix for each of the three sequence networks. (b) Assume the system to be operating at nominal system voltage without prefault currents when a bolted single-line-toground fault occurs on phase A at bus 3. Compute the fault current, the current out of phase C of machine 2 during the fault, and the line-toground voltages at the terminals of machine 2 during the fault. Total detailed answer is needed. The figure is attached.
Why are resistors and inductors considered to be series impedance and capacitors considered as shunt impedance in transmission line modeling?
Establish Zbus matrix for the system shown in figure below using Direct Method and add the lines in the sequence, 1-0, 2-0, 3-1, 1-2, 2-3 as denoted in the figure?
Determine the bus voltages at buses 2 and 3 after 1st iteration using GS method. Take the acceleration factora=1.6
Discuss the advantages and limitations of Gauss-Seidal and Newton Raphson methods . Of this two, which method is generally preferred for solving the load flow problems?
Compare Equivalent- π and Nominal-π in transmission lines. What are their diffirences? When we use them, in order to do what ?Thank you
In power flow studies,if a network consists of a generator bus which elements of Jacobian Matrix will be neglected or become null ? why ?
Which of the following is correct for power flow equation under steady state? Load angle is directly proportional to voltage at infinite bus Load angle is directly proportional to generated voltage Load angle is inversely proportional to voltage at infinite bus Load angle is inversely proportional to reactance of the line