Q:- A solid circular cylinder of diameter 100 mm and length 200 mm slides inside a vertical smooth pipe that has inside diameter 100.5 mm. The small space between the cylinder and the pipe is lubricated with an oil film that has viscosity 3 N.s/m2.The cylinder weight 20 N and concentric with the pipe as it falls .Find the rate of the changer in velocity of the cylinder? Pbe cylinder O Flm

Q:- A solid circular cylinder of diameter 100 mm and length 200 mm slides inside a vertical smooth pipe that has inside diameter 100.5 mm. The small space between the cylinder and the pipe is lubricated with an oil film that has viscosity 3 N.s/m2.The cylinder weight 20 N and concentric with the pipe as it falls .Find the rate of the changer in velocity of the cylinder? Pbe cylinder O Flm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pipe whose axis is horizontal, is full of water in motion. At a section A, the velocity of water is recorded as 54000dm/hrandd the pressure is equilavent tp 14.07m of water. if the pipe tapers gradually from 150mm diameter to A to 100mm diameter at B. determine the preesure at B.
Determine the surface tension in a tube with 0.3m radius and wetting angle 80 and capillary rise of 4.5mm in N/m and in lb/ft.
U - tube is used to pressure the difference in water channel. p1= 1000 kg/m3. The orange fluid in the U - tube has a density: p2= 2000 kg/m3. The height a = 10 cm and h = 15 cm. If the pressure at point ① is 111 kPa, what is the pressure at point ② ?
Q4: Answer A or B A-Ethyl alcohol flows in the pipe as shown in Figure below of specific weight 49 lb/ft3. What is the mass flow rate? If viscous effects are neglected. Take the specific weight for the mercury equal to 846 and for water equal to 62.4 at 68 0F.
Q6) The space between two parallel plates is filled with oil. Each side of the plate is 60 cm. the thickness of oil film is 12.5 mm. The upper plate, which moves at 2.5 metre per sec requires a force of 98.1 N to maintain the Speed. Determine
The oil flows through the vertical venturi tube as shown in the figure. The venturi inlet has a diameter of 20 cm, the isthmus of the venturi is 10 cm in diameter, the pressure at inlet P1 is 41.4 kPa(gage), and the pressure at the isthmus P2 is the same size as the body of water. The same oil which is 1.52 m. Find the flow rate of this oil. The density of the oil is 849 kg/m3.
An oil (viscosity 1 Pa.s, density 800kg/m3) is flowing in an axisymmetric pipe. The flow is fully developed and laminar and the velocity at the centre of the pipe is = 30cm/s. The velocity cross-sectional profile is parabolic as: u(r) = U0(1- r2/R2) . Here r is the distance of the point to the pipe centre where the velocity is u(r). . R is radius of pipe (R=4mm). Calculate: the shear stress at the pipe wall the shear stress within the fluid 2 mm from the pipe wall the Reynold’s number of the flow
Q1: In a venturemeter used for measuring the flow ofoil (-0.85) through a horizontal pipeline, the pipe diameter is 2.4 times the diameter at the throat. Connections are made from the entrance to the meter and the throat to a vertical L tube containing mercury If the difference level between the fluids in the U - tube arms is (x +) in em, where S.N. is student serial number. Neglect friction in the pipe. Find an expression in terms of x for the velocity of the oil in the pipe.
A pump discharges 8000 liters per minute of a certain brine solution (SG=1.20) to an evaporating pond. The intake line is 25cm in diameter and is at the same level as the pump discharge line, which is 15cm in diameter. The pressure at the inlet of the pump is -170mm of mercury. The pressure gage connected to the pipe discharge reads 150 kPa, and its center is 2.0mabove the center of the discharge flange. The vapor pressure of the brine solution is 40mm of Hg. If the pump efficiency is 80%. How much power is required?
A shaft 70-mm in diameter is being pushed at a speed of 400mm/s through a bearing sleeve 70.2-mm in diameter and 250mm long. The clearance is filled with oil with a kinematic viscosity of v = 0.005 ?2/? and SG=0.9. Find the frictional resistance exerted by the oil on the shaft in Newtons (N).
The ethanol solution is pumped into a vessel 25 m above the reference point through a 25 mm diameter steel pipe at a rate of 8 m3 / hr. The pipe length is 40 m and there are 2 elbows. Calculate the power requirements of the pump. The properties of the solution are density 975 kg / m3 and viscosity 4x 10-4 Pa s. a. Reynold number = Answer. b. Loss of Energy along the straight pipe = AnswerJ / kg. c. Losing Energy at curves = AnswerJ / kg. d. Total energy to overcome friction = AnswerJ / kg. e. Energy to increase water according to height = AnswerJ / kg. f. The theoretical energy requirement of the pump ethanol / second = AnswerJ / kg. g. Actual pump power requirement = Answerwatt.
1. in a section of horizontal piper with a diameter of 3cm the pressure is 5.21 kpa and water is flowing with a speed of 1.50m/s. the pipe narrows to 2.50cm. what is the pressure in the narrower region if water behaves like an ideal fluid of sensity 1000kg/m3 2. tensile stress a. the ratio of elasic modules to strain b. the applied force per crosssectional area c. the ratio of change in length to the orig length d. the strain per unit legth e. the same as force