Q.1) Two torques are applied to the solid bronze (G= 6500 ksi) shafts of a gear system shown below. The diameters of shafts AB and CD are 1.25 inch and 1.0 inch, respectively. The shaft CD ix fixed at D and the bearings at A, B, and C are frictionless. Determine the maximum shear stress in each of the shaft and the rotation of end A. 10 in. D 30 in. 80 lb·ft 40 lb·ft 8 in. 10 in. 6 in. B 4 in. 12 in.

Q.1) Two torques are applied to the solid bronze (G= 6500 ksi) shafts of a gear system shown below. The diameters of shafts AB and CD are 1.25 inch and 1.0 inch, respectively. The shaft CD ix fixed at D and the bearings at A, B, and C are frictionless. Determine the maximum shear stress in each of the shaft and the rotation of end A. 10 in. D 30 in. 80 lb·ft 40 lb·ft 8 in. 10 in. 6 in. B 4 in. 12 in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa, nor an allowable rate of twist of 0.75º/m. For G = 78GPa, determine: a. The required diameter do of the solid shaft.b. The required outer diameter d2 of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter.c. The ratio of diameters (that is, the ratio d2/do and the ratio of the weights of the hollow and solid shafts.
The design specifications for the gear-and-shaft system shown require that the same diameter be used for both shafts and that the angle through which pulley A will rotate when subjected to a 2-kip·in. torque TA while pulley D is held fixed will not exceed 7.5°. Determine the required diameter of the shafts if both shafts are made of a steel with G= 11.2 × 106 psi and τall= 12 ksi.assuming that both shafts are made of a brass with G= 5.6 × 106 psi and τall= 8 ksi.
A hollow steel (G = 12,000 ksi) shaft has diameters of 6 in. and 4 in. and an allowable shearing stress of 9,000 psi. Determine a. the horsepower transmitted at 25 rad/sec; b. the magnitude of the angle of twist in a length of 10 ft; and c. the required number of 3⁄4-in diameter bolts for a flange coupling in which two-thirds of the bolts are on a 12-in diameter bolt circle and one-third are on a 9-in diameter circle. The allowable shearing stress in the bolts is 12,000 psi.
A solid circular shaft is acted upon by thetorques as shown. If G= 12, 000 ksi determine:a. Rotation of wheel D with respect to A.b. Shear stress at point EDiameter of shaft:A-B = 2inC-D = 2inB-C = 4inT1 = 2.5 π in.kipsT2 = 8.5 π in.kipsT3 = 7 π in.kipsT4 = π in.kips
Determine the maximum torque that can be applied to a hollow circular steel shaft of 100mm outer diameter and 80mm inner diameter. The shear stress is limited to 70 MPa, and the angle of twist must not exceed 0.4 degrees in a length of one meter. Use G = 83 GPa for steel.
A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa, nor an allowable rate of twist of 0.75º/m. For G = 78GPa, determine: The required diameter do of the solid shaft. The required outer diameter d2 of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter. The ratio of diameters (that is, the ratio d2/do and the ratio of the weights of the hollow and solid shafts. 1
Gear B supplies 15 kW of power, while gears A, C and D withdraw 6 kW, 4 kW and 5 kW, respectively. If the shaft is made of steel with the allowable shear stress of tallow = 75 MPa, and the relative angle of twist between any two gears cannot exceed 0.05 rad, determine the required minimum diameter d of the shaft to the nearest millimeter. The shaft is rotating at 600 rpm.
An aluminum shaft with a constant diameter of 50mm is loaded by torques applied to gears shown. Using G=28GPa, determine the angle of twist of gear D relative to gear A.
An aluminum shaft with a constant diameter of 70 mm is loaded by torques applied to gears attached to it. Use G = 28 GPa, Determine the relative angle of twist of gear D relative to gear A (in degrees). What is the direction of the rotation of A relative to D?
A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa, nor an allowable rate of twist of 0.75º/m. For G = 78GPa, determine: The required diameter doof the solid shaft.g The required outer diameter d2of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter. 3.The ratio of diameters (that is, the ratio d2/do and the ratio of the weights of the hollow and solid shafts.
A flywheel is to be fitted on a punching machine with 73% mechanical efficiency. The machine makes 20 working strokes per minute. The holes are 20-mm diameter, thickness of 12 mm steel plates with an ultimate shear strength of 330 MPa. The punching operation takes place during 1/9th of a revolution of the crankshaft. Determine the capacity (kW) of a driving motor necessary to operate a punching machine.
An aluminum shaft with a constant diameter of 60 mm is loaded by torques applied to gears attached to use it. Use G= 28 GPa. a. Determine the relative angle of twist of gear D relative to gear A (in degrees) b. What is the direction of the rotation of A relative to D?