The solid shaft shown is formed of a brass for which the allowable shearing stress is 55 MPa. Neglecting the effect of stress concentrations, determine the smallest diameters dARand dRc for which the allowable shearing stress is not exceeded. Take Tc= 500 N-m. T 1200 N - m Te dAB 750 mm dBc C 600 mm mm. The smallest diameter dAB is The smallest diameter dgC İS mm.

The solid shaft shown is formed of a brass for which the allowable shearing stress is 55 MPa. Neglecting the effect of stress concentrations, determine the smallest diameters dARand dRc for which the allowable shearing stress is not exceeded. Take Tc= 500 N-m. T 1200 N - m Te dAB 750 mm dBc C 600 mm mm. The smallest diameter dAB is The smallest diameter dgC İS mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa, nor an allowable rate of twist of 0.75º/m. For G = 78GPa, determine: The required diameter doof the solid shaft.g The required outer diameter d2of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter. 3.The ratio of diameters (that is, the ratio d2/do and the ratio of the weights of the hollow and solid shafts.
A hollow steel shaft 3 m long delivers 2.6 MW of power while rotating at 1000revolutions per minute. The total angle of twist in this length is not to exceed 3oand the allowable shearing stress is 85 MPa. Determine the inside and outsidediameter of the shaft. Use G = 85Pa.
A solid steel shaft will not twist through more than 3 degrees in a 6-m length when subjected to atorque of 12 KN"m. The modulus of rigidity of the steel shaft is 83 GPa. Determine;a) Diameter of the shaft.and Maximum shearing stress developed in the shaft.
A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa, nor an allowable rate of twist of 0.75º/m. For G = 78GPa, determine: The required diameter do of the solid shaft. The required outer diameter d2 of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter. The ratio of diameters (that is, the ratio d2/do and the ratio of the weights of the hollow and solid shafts. 1
Determine the maximum shearing stress(MPa) that can be developed in a solid steel shaft if it will not twist through more than 3.1° in a 5.6-m length when subjected to a torque of 18.0 kN-m? Use G = 81 GPa.
A hollow circular shaft with the ratio of internal and external diameters of 0.6 is required to transmit 870 kW at 120 rpm, the maximum torque being 20% greater than the mean. Determine the dimensions of the shaft if the maximum shearing stress and twist in a length of 3m are limited to 60Mpa and 1.4°respectively. The G= 80Gpa.
A steel shaft 2ft long that has a diameter of 4in. is subjected to a torque of 12kip-ft. Determine the maximum shearing stress and the angle of twist. Use G= 12 x 106psi
A circular solid shaft made of vibranium has G=80 Mpa and has a limiting torsional shear stress of 60 Mpa. Allowable angle of twist is 0.03 rad. Determine the minimum required diameter if T1=10kN-m and T2=25kN-m. Answer in mm.
A solid shaft is to transmit 22kW at 110 rpm. Determine the diameter of the shaft if the shearing stress is not exceed 35 MPa and the angle of twist is limited to 5 degrees in a length of 4m. Use G=86 GPa.
What is the minimum diameter of a solid steel shaft that will not twist through more than 3.18 degrees in a 6 m length when subjected to a torque of 14KN-m. What maximum shearing stress is developed? Use G=83GN/m^2.
A solid shaft having a diameter of 100mm has an allowable shearing stress of 80 MPa. Determine the maximum torque in KN-m that the shaft can carry without exceeding the allowable shearing stress.
The solid rod AB has a diameter dAB5 60 mm and is made of a steel for which the allowable shearing stress is 85 MPa. The pipe CD, which has an outer diameter of 90 mm and a wall thickness of 6 mm, is made of an aluminum for which the allowable shearing stress is 54 MPa. Determine the largest torque T that can be applied at A