Q1: A 3-phase of sequence ABC transmission line has a conductors of cross section area (82 mm²) and a diameter of (1 cm) as shown in figure below. Delivers a load of 15 MW at 30 kV and power factor of 0.78. Determine the efficiency and voltage regulation of the line. If the line length (65km). The line is completely transposed. For the copper p 1/58 per meter length. 3 m 6m 4

Q1: A 3-phase of sequence ABC transmission line has a conductors of cross section area (82 mm²) and a diameter of (1 cm) as shown in figure below. Delivers a load of 15 MW at 30 kV and power factor of 0.78. Determine the efficiency and voltage regulation of the line. If the line length (65km). The line is completely transposed. For the copper p 1/58 per meter length. 3 m 6m 4

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.18P

See similar textbooks

Similar questions

A 40-km, 220-kV, 60-Hz, three-phase overhead transmission line has a per-phase resistance of 0.15/km, a per-phase inductance of 1.3263 mH/km, and negligible shunt capacitance. Using the short line model, find the sending-end voltage, voltage regulation, sending-end power, and transmission line efficiency when the line is supplying a three-phase load of (a) 381 MVA at 0.8 power factor lagging and at 220 kV and (b) 381 MVA at 0.8 power factor leading and at 220 kV.
A single-phase overhead transmission line consists of two solid aluminum conductors having a radius of 3 cm with a spacing 3.5 m between centers. (a) Determine the total line inductance in mH/m. (b) Given the operating frequency to be 60 Hz, find the total inductive reactance of the line in /km and in/mi. (c) If the spacing is doubled to 7 m, how does the reactance change?
Calculate the capacitance-to-neutral in F/m and the admittance-to-neutral in S/km for the three-phase line in Problem 4.18. Also calculate the line-charging current in kA/phase if the line is 110 km in length and is operated at 230 kV. Neglect the effect of the earth plane.
Transmission line conductance is usually neglected in power system studies. True False
If the per-phase line loss in a 70-km-long transmission line is not to exceed 65 kW while it is delivering 100 A per phase, compute the required conductor diameter if the resistivity of the conductor material is 1.72108-m.
PowerWorid Simulator case Problem 3_60 duplicates Example 3.13 except that a resistance term of 0.06 per unit has been added to the transformer and 0.05 per unit to the transmission line. Since the system is no longer lossless, a field showing the real power losses has also been added to the oneline. With the LTC tap fixed at 1.05, plot the real power losses as the phase shift angle is varied from 10 to +10 degrees. What value of phase shift minimizes the system losses?
A 60-Hz, single-phase two-wire overhead line has solid cylindrical copper conductors with a 1.5 cm diameter. The conductors are arranged in a horizontal configuration with 0.5 m spacing. Calculate in mH/km (a) the inductance of each conductor due to internal flux linkages only, (b) the inductance of each conductor due to both internal and external flux linkages, and (c) the total inductance of the line.
The following parameters are based on a preliminary line design: per unitVS=1.0, VR=0.9 per unit, =5000km,Zc=320,=36.8. A three-phase power of 700 MW is to be transmitted to a substation located 315 km from the source of power. (a) Determine a nominal voltage level for the three-phase transmission line, based on the practical line-loadability equation. (b) For the voltage level obtained in part (a), determine the theoretical maximum power that can be transferred by the line.
Solve this math : A three-phase 60-hz transmission line has its conductors arranged in a triangular formation so that two of the distances between conductors are 20ft and the third is 40 ft. The conductors are ACSR Rook. Determine the capacitance to neutral in microfarads per mile and the capacitive reactance to neutral in ohm-miles. If the line is 115 mi long, find the capacitance to neutral and capacitive reactance of the line. Note: In the below i have added similer type of math and its ans.In the above math, there is just changes of values and Main Change is ACSR ROOK which is given to then question and in the below question which is solved it was ask ACSR Parakeet. So notice that. Follow This Book for help"POWER SYSTEM ANALYSISAND DESIGN;FIFTH EDITION, SI;J. DUNCAN GLOVER" Now solve the math according to the given way solve the math. "A three-phase 60-hz transmission line has its conductors arranged in a triangular formation so that two of the distances between conductors are 25…
Given a three-phase load of 125 MW at power factor of 0.8 lagging, operating at 69kV, with a transmission line efficiency of 97% and voltage regulation of 95%, and the line length of 50 km, design a transmission line system and determine the best conductor configuration, conductor resistance and inductance, and conductor radius values to achieve the efficiency and voltage regulation set. Assume a two-bundled conductor configuration with GMR of 0.0496 m and bundle spacing of 30 cm.
Estimate the distance over which a load of 15000 kW at 0·85 p.f. can be delivered by a 3-phase transmission line having conductors of steel-cored aluminum each of resistance 0·905 Ω/phase per kilometer. The voltage at the receiving end is to be 132 kV and the loss in transmission is to be 7·5% of the load.
In three-phase short transmission line with end-of-line interphase voltage UR = 31,5kV , from the end of the line active power absorbed PR = 9000 kW, end of line power factor is cosφ = 0,70 (end) and the length of the line is l = 20km, The resistance of the line per km is R'= 0,125 Ohm/km, the reactance per km is X'= 0,375 Ohm/km.With the help of given information; a) Calculate the current drawn from the line (IR) as a phasor. b) Calculate the line-to-line-neutral voltage (VS) as a phasor, determine the effective line-to-line voltage (US) Calculate its value. c) Calculate the line head power factor, active and reactive power drawn from the line head, d) Draw the phasor diagram of the system. ..