Q1 (a) A container fill with an unknown liquid has three holes as shown in Figure Q1 (a). Determine the difference between the flow rates of the first hole and the third hole when height a and diameter d are 0.5 m and 10 mm respectively.

Q1 (a) A container fill with an unknown liquid has three holes as shown in Figure Q1 (a). Determine the difference between the flow rates of the first hole and the third hole when height a and diameter d are 0.5 m and 10 mm respectively.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

According to Torricelli´s theorem, the velocity of a fluid discharging through the hole of a reservoir is V=(2gh)^1/2, where h is the height of water above the hole, as shown in the figure. If the hole has a section Ao and the reservoir is cylindrical with a cross-section of area Ab>>Ao. Obtain a formula for the time it will take for the reservoir to completely empty if the initial height of the water is ho.
Two identical upright cylindrical tanks contains H2O,the first tank is full and the second is 2/3-full. If theradii of the orifices are the same, compare the time todrain of each tank. answer: √1.5
A 1.0 m radius cylindrical industrial tank filled with viscous oil to a level at a height h from its base, must be drained through a tube with a radius of 0.2 m and length L, connected to its base. The speed profile of oil in the drain tube can be described by the equation below. Where v is the oil speed, vmax is a = maximum oil speed, r is the radius, and R is the tube radius. Considering this problem situation, do what is asked in the following items, justifying your answers. a) What is the volume, in liters, of oil removed from the tank after 10 seconds, if the maximum discharge speed does the oil reach 0.35 m/s? Data: π ≈ 22/7; 1 m3 = 1000 L. b) What flow regime does the system operate? Demonstrate. Data: specific mass of oil = 800 kg/m3, specific mass of water = 1000 kg/m3, oil viscosity = 0.056 Pa.s e viscosity of water = 0.001 Pa.s.
A pipe discharges 142 lps of water into a reservoir at a point 1.85 mbelow the water surface. At point A the diameter is 25.4 cm and the center of thepipe is 1.25 m above the water surface. At the discharge end the pipe is 30.5 cm.If the head loss from A to the reservoir is 0.7 m, determine the pressure in A.
The ideal fluid (water) taken from the infinitely sized chamber A with the chamber-pipe system in the figure with a fixed diameter 40 cm BCDEF pipe. is poured into the atmosphere , Since zB=29 zC=10, zD=28.5, zE=5 and zF=28 with respect to the reference plane meters; a)determine the flow rate of the system b)draw the relative load (energy) and piezometer level lines c)determine where the greatest pressure will be observed throughout the system and calculate its relative value
Water flows through an orifice at the vertical side of a closed cylindrical tank. The water level inside the tank remains constant at 3m and the pressure at the top of the tank is 30KPa. If the jet strikes the ground horizontally by 4.5m and below the vena contracta by 1m, determine the coefficient of velocity.
A jet of liquid is directed vertically upward. At A its diameter is 75 mm and its velocity is 9 m/s. Neglecting air friction, determine its diameter at a point 3 m above A.A.104 mm.C.100mm.B.102 mm.D.106mm.
The oil flows through the vertical venturi tube as shown in the figure. The venturi inlet has a diameter of 20 cm, the isthmus of the venturi is 10 cm in diameter, the pressure at inlet P1 is 41.4 kPa(gage), and the pressure at the isthmus P2 is the same size as the body of water. The same oil which is 1.52 m. Find the flow rate of this oil. The density of the oil is 849 kg/m3.
Read the question carefully and give me all right solutios. A 2.4 m diameter tank is initially filled with water 5.5 m above the center of a 10 cm diameter, sharp-edged hole. The surface of the water tank is open to the atmosphere, and the hole drains to the atmosphere. If you neglect the effect of the kinetic energy correction factor, calculate: a) the initial flow rate of the tank and b) the time it takes to empty the tank.c) Does the orifice loss coefficient cause a significant increase in tank drain time? yes or no, the emptying time for this case is t =
A tap discharges water evenly in a jet at a velocity of 2.5 m/s at the tap outlet, the diameter of the jet at this point being 15 mm. The jet flows down vertically in a smooth stream. Determine the velocity and the diameter of the jet at 50-cm below the tap outlet.
At the bottom of a pressurized water tank is a mouth with a diameter of 5 cm, where water is discharged into the atmosphere. The water level is 2 m above the outlet. The tank air pressure above the water level is 300 kPa (absolute) and the atmospheric pressure is 100 KPA. Determine the initial rate of water discharge (volumetric flow rate) from the tank, neglecting the effects of friction.
The pressure in a section of a horizontal pipe of diameter d1 = 2.0 cm is p1 = 142 kPa. The water flows through the pipe at a volumetric flow rate V = 2.8 L/s. If the pressure at a certain point is reduced to p2 = 42.6 kPa, due to a throttling of a pipe section, what should the diameter d2 of the throttling section be? Consider the density of water ρ = 1.0 g/cm3. Choose the correct option: