Q1 \ A d.c series generator has armature resistance of 0.5 Q, and series field resistance of 0.032 .It drives aload of 50 A. if it has 6 turns\coil and total 540 coils on the armature and is driven at 1500 r.p.m., calculate the terminal voltage at the load. Assume 4 poles, lap type winding, flux per pole as 2 mWb and total brush drop as 2V.

Q1 \ A d.c series generator has armature resistance of 0.5 Q, and series field resistance of 0.032 .It drives aload of 50 A. if it has 6 turns\coil and total 540 coils on the armature and is driven at 1500 r.p.m., calculate the terminal voltage at the load. Assume 4 poles, lap type winding, flux per pole as 2 mWb and total brush drop as 2V.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.48P

See similar textbooks

Similar questions

A 4 pole dc shunt generator with a shunt field resistance of 100 ohm and an armature resistance of 1 ohm has 378 wave connected conductor in its armature. the flux per pole is 0.02wb, if the load resistance of 10 ohm is connexted across the aemature terminal and the generator driven at 1000rpm, calculate the power obsorbed by load
Q2: A500 kW , 500 V, 10 poles d.c generator has lap wound armature Find the electrical angle shift of brushes when ATd / pole = 208 AT . If the ATC for same generator when connected as wave wound is 2600 AT when the brushes on G.N.A .
PUT THE EQUATION Given a progressive 2-layer simplex lap winding for a 4-pole dc generator having 20 slots and 20 commutator segments, determine the following and input it on the text field provided. determine: a.Coil Pitch, Ys b.Commutator Pitch, Yc, Back Pitch, YB d. Front Pitch, YB, No. of Parallel Paths
A short shunt compound generator supplies a load of 10 kW at 200 V through a pair of feeder and series field resistance 0.10 ohm. Armature resistance, shunt field resistance and series field resistance are 0.01 ohm, 52.2 ohms and 0.10 ohm, respectively. If the core friction and windage losses amount to 631 watts, the BHP of the driving engine is nearest to
Q2: A500 kW, 500 V, 10 poles d.c generator has lap wound armature Find the electrical angle shift of brushes when AT4 / pole = 208 AT. If the ATC for same generator when connected as wave wound is 2600 AT when the brushes on G.N.A.
A long shunt compound DC generator delivers a load current of 150A at 230V and has armature, series field and shunt field resistances of 0.032, 0.015 and 92Ωrespectively. Calculate (i) induced emf (ii) total power generated and (iii) distribution of this power (iv) voltage regulation
A three-phase Y-connected synchronous generator has rated values of 90 MVA, 15 kV, 0.6 reverse power factor, 50-Hz. Synchronous reactance 1.6 ohmsand armature resistance is neglected. According to thisa) Find the induced voltage (EA) and armature current (LA). b) Find the voltage regulation.c) If this generator was operated at 60 Hz with the same armature and field losses as at 50 Hz; What would be the voltage, apparent power and reactance of the generator
Problem: The field current of a 100-kW, 250V shunt generator is 5A when delivering power at rated terminal voltage and rated load current. The combined armature and brush resistance is 0.1 ohm. 1.)Calculate the generated power in kW. 2.)What is the electrical efficiency? * Formatt: given required solution answer
The synchronous reactance of the direct-axis and quadrature-axis of a three-phase,40-pole, 50 Hz, 13,8 kV, salient-pole synchronous generator is 2,38 Ω and 1,33 Ωrespectively. The resistance of the star-connected stator is negligible. The load angle ofthe machine is 30°e and the excitation is set to induce an emf of 167%. Sketch the phasordiagram and calculate:(a) current(b) power(c) reluctance torque(d) the maximum load angle(e) the maximum power developed
A 20 kW, 440-V, short-shunt, compound d.c. generator has a full-load efficiency of 87%. If theresistance of the armature and interpoles is 0.4 Ω and that of the series and shunt fields 0.25 Ωand 240 Ω respectively, calculate the combined bearing friction, windage and core-loss of themachine.
. A 480-V 200-kVA 0.8-power-factor-lagging 60-Hz two-pole Y-connected synchronous generator has asynchronous reactance of 0.25 Ω and an armature resistance of 0.03 Ω. At 60 Hz, its friction and windagelosses are 6 kW, and its core losses are 4 kW. The field circuit has a dc voltage of 200 V, and themaximum IF is 10 A. The resistance of the field circuit is adjustable over the range from 20 to 200 Ω.The OCC of this generator is shown in Figure P5-1.(a) How much field current is required to make VT equal to 480 V when the generator is running at noload?(b) What is the internal generated voltage of this machine at rated conditions?(c) How much field current is required to make VT equal to 480 V when the generator is running at ratedconditions?(d) How much power and torque must the generator’s prime mover be capable of supplying?
In a three-phase, Y-connected, 750-kVA, 1732-V, synchronous generator afield current of 20 A at the rated speed produces a current of 300 A onshort circuit and a voltage of 1732 V on open circuit. The resistance betweenany two terminals of the generator is 0.8 R. Determine the synchronousreactance of the generator. The rotational loss is 20 kW. Using the per-unitsystem, determine the voltage regulation and the efficiency of the generatorwhen it delivers the rated load at its rated voltage and unity power factor.