Q1/ Answer the following questions: 1. We can classify I.C. engines to give a clear description for any engine? Give your opinion about that. 2. Side thrust force may give an indication about the engine performance. Discuss that. 3. It is possible to increase the mechanical efficiency of the turbocharger. Do you agree? Why? 4. How is the friction force reduced? 5. If the engine designers reduce the piston skirt length as much as possible, is this considered as an advantage for the I.C. engine?

Q1/ Answer the following questions: 1. We can classify I.C. engines to give a clear description for any engine? Give your opinion about that. 2. Side thrust force may give an indication about the engine performance. Discuss that. 3. It is possible to increase the mechanical efficiency of the turbocharger. Do you agree? Why? 4. How is the friction force reduced? 5. If the engine designers reduce the piston skirt length as much as possible, is this considered as an advantage for the I.C. engine?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If the volumes at the end of compression and at the beginning of expansion in an ideal Diesel engine are 0.039 m³ and 0.041 m³ respectively. What is the cut-off ratio?
12. A 1.8-liter, 6-cylinder engine behaves as a polytropic air system with n=1.2. At the beginning the volume of air inside the cylinder is Vo=1/8 Vcylinder, the temperature and pressure are 25 °C and 77 KPa. At the end of the expansion, the temperature is 350°C and the volume is that of the cylinder. A. What is the pressure at the end of the cycle? B. If 40% of the boundary work is used to accelerate a 400 kg car. How long does it take for the car to go from 0 to 100 at 2000 RPM?
Explain the basic workings of an engine. Be sure to discuss the engine in terms of thermodynamic terminology. Give two examples of engines.
Interpret the engine performance based on the established parameters such as mechanical efficiency, engine efficiency and thermal efficiency and demonstrate the effect of altitude in the engine performance.
The effort to build an engine which is 100% efficient is:Will be achieved some dayNot PossiblePossibleIs slightly delayed
Suppose that a new gasoline engine has been invented which can operate at the maximumthermodynamic efficiency (rather than the 25% or so which characterize most realisticengines). The burned fuel reaches about 2100 degrees C inside the engine and a 50 L gas tank has about2 GJ of fuel energy. If the engine must supply 30 hp to keep the car at a steady speed on the highway, how long will a tank of gas last?
b) 3.02 C) 4500 D) 55 F) 10244 can I get some help with efficiency recalculation Repeat the analysis entropic efficiency of 84% and each pump operates with an isentropic efficiency of 78%. Provide a table comparing the results of this analysis to those from Problem4 and comment on the effect of a non‐ideal cycle.
please answer everything Consider an ideal air-standard diesel cycle engine, with an inlet temperature of 293-K and a compression ratio of 20. Heat added is 1235-kJ/kg. Find T2, T4, the cut-off ratio(V3/V2), and the efficiency of the cycle. Assume air standard values for R and k. a. The value of T2. (in Kelvin) b. The value of T4. (in Kelvin) c. The cut-off ratio. (V3/V2) d. The efficiency of the cycle. (in %)
. Suppose someone wants you to invest money in anautomobile engine, claiming that it will produce moreenergy than is found in the fuel used to run it. Whatwould be your response? Explain.
What is the fact that at some speed the volumetric efficiency of an engine is maximum, however it decreases gradually at the start and end.
The conditions at the beginning of compression in an Otto engine are 101.3 kPaa, 0.66 m^3 and 38.0 C. If the volume at the beginning of the isometric heat addition is 0.06 m^3, what is the percent clearance?
Q:What is the difference between a diesel engine and a gasoline engine, and when to use both engines?