Answered: Q1:-The gate AB as shown in fig.1 has…

Name: Q1:-The gate AB as shown in fig.1 has long 1 m and wide 0.9 m.Find th
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Q1:-The gate AB as shown in fig.1 has long 1 m and wide 0.9 m.Find the forceF on The gate AB and also find the centre of pressure X8 m3 m1 mOilA1 mS=0.817 mB50Fig.1

Engineering

Mechanical Engineering

Q1:-The gate AB as shown in fig.1 has long 1 m and wide 0.9 m .Find the force F on The gate AB and also find the centre of pressure X 8 m 3 m 1m Oil A 1 m S=0.81 7 m 50 LL

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Neglect the thickness of the bar. Take ua=ub=u suppose that b= 1 ft
Find a) the total force on gate AB in KN and b) the position of the center of pressure in m with respect to the bottom of the pond. Assume that the gate is 8 feet wide, that 1ft = 0.3048m, and that 1 psi = 6897.1 Pa. Relative density salt water 1.025.
A 27 m vertical column of fluid (density 1878 kg.m3) is located where g= 9.65 m/sec2. Find the pressure at the base of the column.Ans. 489.313 kPa Please give me the solution.
A thin-walled hollow sphere 3.8 m in diameter holds helium gas at 1767 kPa. Determine the minimum wall thickness of the sphere in mm if its allowable stress is 84.8 MPa.
A cylindrical tank having a pressure of 114.0 kPa is used to carry a 3.5 m3of water has a height of 2.0 m and thickness of 5.0 mm. Determine the following What is the diameter of the tank The tangential and longitudinal stress in the tank
2. A 3,000 gallon tanker is carrying industrial alcohol (donaity-48 23 D. /h) finteBurton to the Selene Building. Find the weight (N) of the industrial alcohol if the tanker is67% full. (Round to nearest whole number)
Show the derivation of the girth and longitudinalstresses of the thin-walled cylindrical container shownbelow. Say p is the internal pressure, d is the insidediameter of the container, and t is wall thickness.
3: T = 10.11 kN-m
A WATER TANK IS “L1” IN DIAMETER AND “L2” HIGH. IF THE TANK IS TO BE COMPLETELY FILLED, DETERMINE THE MINIMUM THICKNESS OF THE TANK IF THE STRESS IS LIMITED TO 70 MPa. (note: Diam = L1, Height = L2) L1 = 5 L2 = 7
Plz answer I will rate !:) A right circular cylindrical tank with its circular base on the ground is full of water. The diameter of the base is 4m and the height of the tank is 4m. Set up a Riemann sum to approximate the hydro static force against the lateral wall of the tank. Then express the force as an integral and evaluate it.
An open tank contains y1 = 8.7m of water covered with y2 = 5.7m of kerosene (y=8 kn/m^3). Find the pressure at the bottom of the tank in kPa.
The strength per meter of the longitudinal joint in the figure is 480 kN, whereas or the girth joint is 200 kN. Determine the maximum diameter of the cylindrical tank if the internal pressure is 1.5 MPa.