Q1. For the single-phase half-wave controlled rectifier with a firing angle of (a = 60°) and with R-L load circuit shown below, draw the output voltage and current waveform. a. Find the extinction angle (B) and conduction angle (8). b. Determine the ripple factor. a = 60° io R = 602 27 ot Vs = v2 240 sin 1207tt Vo 200mH

Q1. For the single-phase half-wave controlled rectifier with a firing angle of (a = 60°) and with R-L load circuit shown below, draw the output voltage and current waveform. a. Find the extinction angle (B) and conduction angle (8). b. Determine the ripple factor. a = 60° io R = 602 27 ot Vs = v2 240 sin 1207tt Vo 200mH

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is CEMF?
A three-phase, half-wave uncontrolled rectifier is fed from an ideal three-phase voltage source of 380V, 50 Hz. The load is resistive with R=15 2. Calculate: (a) The average output voltage and average load current of the rectifier. (b) The d.c. and a.c. power dissipations in the load. (c) The diode ratings. (d) What is the lowest ripple frequency of the output voltage waveform?
Q.1 A single-phase diode bridge rectifier is connected to a grid with rms voltage V, 230V at 50 Hz. Assume that the load is highly inductive, so it could be represented by a constant dc current, Id = 10A. a) Sketch the load voltage and find the average voltage of the load? b) Sketch the source current (grid. AC side) and find the rms value of the source current? c) Determine the fundamental source current and the first three harmonics? Assume Ish_rms ³ 0.91a/h for odd hand 0 otherwise?
The secondary input voltage to a single phase diode bridge rectifier is 50V, 50Hz, and the load can be replaced by a resistance of value 20ohms (a) Sketch a well labelled circuit of the converter described above. (b) Sketch the waveforms for the input voltage, output voltage, output current, and output current (c) Derive an equation for average output voltage and calculate for output dc voltage (d) Calculate the ripple factor of the output voltage (e) Transformer utilization factor (h) How can the ripple be improved
Calculate the rms load current for the single phase uncontrolled half-wave rectifier when the source voltage of 200V at a frequency of 50Hz, and load resistance is 10ohm.
In a center-tapped full wave rectifier circuit utilizing ideal diodes, if the primary voltage is 160Vpeak, the turns ratio is 8:1 and the load resistance is 860 ohms, what is the rectified dc voltage at the output? express answer in volts
Setup the Half Wave Rectifier using LiveWire Simulation software for the given below values.f=1HZVs=5V
A single-phase fully controlled, full-wave, bridge rectifier has a source of 220 V rms at 50 Hz. The firing angle α = 45˚ and the current extinction angle β =255˚; (i) Determine whether the current is continuous or discontinuous and write the condition. (ii) Sketch the appropriate load voltage and load current waveform. (iii) If the firing angle is increased into 110˚, state the polarity of voltage and power for that condition.
Consider the full-wave rectifier circuit shown below, where• vS(t) is a sinusoidal signal with a peak value (Vs = 5 V).• Diodes are modelled using constant voltage model with VDO = 0.7 V• The ac line voltage has an rms value of 120 V and a frequency (f) = 60 Hza) Calculate the transformer turns ratio. b) Plot in the same graph signal vS(t) and the output signal vO(t) versus time (t) (show all details including amplitudes, time instances, etc.) c) Calculate the rms value of the output signal vO(t). (hint: sin2(x) = 0.5(1- cos(2x))) d) If a capacitor C=3.58 F is connected across R = 10 k, repeat (b) in a new graph
1. A single-phase, 120V, 50Hz supply is connected to a controlled half-wave thyristor rectifier and series R-L load consisting of a resistor R of 350 ohms and inductor L of 150mH. The thyristor firing angle is 65 degrees. Assume the diode and thyristor are ideal. i) calculate the dc load voltage VDC and the load dc current IDC. ii) briefly explain why a freewheeling diode is often connected in parallel to an R-L connected load in rectifier circuits
What is the PIV rating of each silicon diode in volts for a bridge type rectifier where the voltage in the secondary transformer is 100V peak? Assume 2.2K ohms load.