Q1/Water at 20'C is being pumped from a storage tank to an elevated second tank at a rate of 0.5 m'/sec. The elevation of the surface of the storage tank is 110 m and the elevation of the second tank is 150 m from sea level. the water discharge pipe is located at a depth of 10 m from the surface of the storage tank The frictional losses in the water line to the plant are given by the relation (0.098 m/s)L, where L is the length of the pipe line. The water line to the supply tank has an inner diameter of 0.05 m and a length of 1200m. How much energy must a pump deliver to the water?

Q1/Water at 20'C is being pumped from a storage tank to an elevated second tank at a rate of 0.5 m'/sec. The elevation of the surface of the storage tank is 110 m and the elevation of the second tank is 150 m from sea level. the water discharge pipe is located at a depth of 10 m from the surface of the storage tank The frictional losses in the water line to the plant are given by the relation (0.098 m/s)L, where L is the length of the pipe line. The water line to the supply tank has an inner diameter of 0.05 m and a length of 1200m. How much energy must a pump deliver to the water?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the loss of head due to sudden enlargement when the velocity of water in the smaller pipe is 12.1 m/s and the velocity of water in the larger pipe is 5.9 m/s. 148.18 m 144.64 m 1.96 m 5.69 m
Water from an open tank elevated 5m above ground is allowed to flow down to a pump. From the pump, it then flows horizontally through 100m of piping, and out into the atmosphere. If there are 2 standard elbows and one wide open gate valve in the discharge line, determine a) all friction losses in the system and b) the power requirement of the pump if it is to maintain 0.8 cubic meters per minute of flow. Assume a pump efficiency of 55%, and that friction is negligible in the pump suction line.
At the Niagara Falls generating station, the water drops 102 m from the intake pipes atthe top of the falls to the turbines below. Calculate the power generated by each tonneof water (1 tonne = 1000 kg) that flows through the station every second. Assume anefficiency of 75 %.
A pump is required to pump water from a large reservoir to the water tower located 20 m above thereservoir (Figure 1). If 0.03 m3/s of water having a density of 1000 kg/m3is pumped through a 30-mmpipe.a. How much power is required to be delivered to the water by the pump? Consider the flow lossesin the pipe; do the necessary assumptions. b. Determine the efficiency of the pump
6. Water is flowing through a pipe having diameter 300mm and 200 mm at the bottom and upper end respectively. The pressure at the lower(bigger) end is 25 N/cm2 and the pressure at the upper end is 10 N/cm2. Determine the difference in datum head if the rate of flow through pipe is 40 lit/s.
To have a complete understanding of the hydraulic system, it is required to determine the efficiency of a water turbine that has atangential velocity of 20 m/sec and works under the head of 60m. The jet is turned through 165o and discharge through the nozzle is100 L/s. Take Cv = 0.97.
The diameter of a pipe carrying oil(s=0.92) changes gradually from 400 mm at A to 600 mm at B. Point A is 3.6 m lower than B. If the pressure at A is 70 KPa and that at B is 49 KPa when 140 L/s is flowing, determine the direction of flow; (b) the frictional loss between the two points.
Water enters a turbine through a 320mm diameter pipe at the rate of 215 lit/s at a pressure at A of 150 KPa and leaves the turbine at a pressure at B of -35 KPa through a 600mm diameter pipe. Point A is 1.2 m higher than B.1. Determine the velocity head at A.2. Solve for the velocity at B.3. What is the expended head by the turbine?4. Determine the power delivered to the turbine by the water.
Given the water tank A in an orifice setup that transfers water to tank B, determine the theoretical and actual velocity and flow rate if the time it takes to fill up tank B is 20 sec.
A water turbine operating at 85% efficiency is under a head of 100 m. If the constant discharge is 1000 gallon/sec, evaluate the operating speed of the turbine.
A pump is designed to fill a pressurized tank rated at 1 MPa anda height of 23 m. Determine the power requirement of the pump inkW if the flowrate is measured at 20 m3/min.
A pump takes water at 60 F from a largereservoir and delivers it to the bottom of anopen elevated tank 25 ft above the reservoirsurface through a 3-in ID pipe. The inlet tothe pump is located 10 ft below the watersurface, and the water level in the tank isconstant at 160 ft above the reservoir surface.The pump delivers 150 gal/min. If the total loss of energy due to friction in the pipingsystem is 35 ft-lb, per 1bm of fluid, calculatethe horsepower required to do the pumping.The pump-motor set has an efficiency of 55%.