Q2: A gas engine working on the Otto cycle has cylinder bore of 200 mm and stroke length of 250 mm. The clearance volume (V) is 1570 cm³. The pressure and temperature at the beginning of compression are p, = 1 bar and T, = 290 K respectively. The maximum temperature of the cycle is 1673 K. Determine the work done; mean effective pressure and air-standard efficiency.

Q2: A gas engine working on the Otto cycle has cylinder bore of 200 mm and stroke length of 250 mm. The clearance volume (V) is 1570 cm³. The pressure and temperature at the beginning of compression are p, = 1 bar and T, = 290 K respectively. The maximum temperature of the cycle is 1673 K. Determine the work done; mean effective pressure and air-standard efficiency.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Hello, this is the problem attached below: An air-standard dual cycle has a compression ratio of 8.6 and displacement of Vd = 2.2 L. At the beginning of compression, p1 = 95 kPa, and T1 = 290 K. The heat addition is 4.75 kJ, with one quarter added at constant volume and the rest added at constant pressure. Determine: a) each of the unknown temperatures at the various states, in K.b) the net work of the cycle, in kJ.c) the power developed at 3000 cycles per minute, in kW.
There are supplied 400 kJ per cycle to an ideal diesel engine operating on 0.5 kg of air. At the beginning of compression, pressure is 100 kPa and temperature is 50 degrees Celsius. At the end of compression, pressure is 4000 kPa. Determine the ff: Compression ratio t2, t3, V3, P4, t4 in degree Celsius, m³ and kPa Heat rejected in kJ Network in kJ Thermal efficiency, % MEP in kPa
In an air standard Brayton cycle the air enters the compressor at 0.1 MPa, 25 ∘C. The pressure leaving the compressor is 1 MPa. and the maximum temperature in the cycle is 1200 ∘C. Assume a compressor efficiency of 80%, a turbine efficiency of 85%, and a pressure drop between the compressor and turbine of 30 kPa. Use the PG model. a) Determine compressor work (w_C), b) Determine the turbine work (w_T), c) Determine the cycle efficiency (n_th,Brayton).
In an Otto cycle air at 27 degree centigrade and 1 bar is compressed adiabatically to 12bar. Heat addition occurs at constant volume and pressure rises to 30bar. Determine the air standard efficiency, compression ratio. Assume Cv= 0.717 KJ/kgK for air.
The Otto cycle should be used to model an engine cycle. Every one of thepresumptions of the ideal Otto cycle should be applied aside from that a polytropicinteraction with n 1.3 will be utilized for the expansion process. The conditionstoward the beginning of pressure is T1 = 333 K, P1 is 90 kPa and the compressionratio is 8. The energy infused into the cycle during the consistent volume process is2000 kJ/kg. Assume constant specific heatsa) Find the expansion work (kJ/kg)b) Find the net heat transfer for the cycle (kJ/kg) diesel
The compression ratio of an Otto cycle is 8, at the beginning of the zanthropic compression process, the pressure of the air is 100 kPa, the temperature is 27 "C, the volume is 550 cm. At the end of the lzantropic expansion process, the temperature of the air is 700 K. Using the specific temperature values at room temperature (according to the cold air standard assumptions) Find the gravity of the air.
An ideal Diesel engine operates on 0.63 lbm of air with a suction state at 14 psia and 140-F. The pressure at the end of compression is 458 psia and the volume at the end of heat addition process is 0.13 cubic ft. Using air properties (R=53.34 ft-lbf/lbm-R, k=1.4, Cp = 0.24, Cv=0.1714 Btu/lbm-R), determine compression ratio, percentage clearance, Qa, Qr, Thermal Efficiency, mean effective pressure. kindly show complete solutions
An oil engine working on a dual combustion cycle, has a compression ratio of 16: 1 and the cut-off takes place at 6% of the stroke. The maximum pressure obtained is 70 bar. The pressure and temperature at the beginning of compression are 1 bar and 110°C respectively. Determine the pressure and teperature at all the important points of the cycle. Assume R = 0.287 kJ/(kg K) and c, = (0.716+ 125 x 10-67) kJ/(kg K)
A two stage compressor with first stage piston displacement of 94,390 cu.m/sec is driven by a motor. Motor output is 35 HP, suction temperature 22 degC, volumetric efficiency is 85%, mechanical efficiency is 95%, the intercooler pressure is 30 psi gage. Air temperature in and out of the intercooler are 105deg C and 44 degC, respectively. Final discharge pressure is 100 psi gage, while suctionis estimated to be 14.4 psi. Determine the compression efficiency.
An incomplete expansion engine is supplied with steam at 1.95 Mpa and 400C. Release occurs at 0.14 Mpa and exhaust at 50C. Test of the engine showed a brake steam rate of 12.2 kg/kwh and a mechanical efficiency of 82.5%. Find (a) the ideal work and the ideal thermal efficiency, (b) the ideal steam rate, (c) the indicated thermal efficiency, (d)the indicated engine efficiency, (e) the brake mep, and (f) the ideal thermal efficiency of an incomplete expansion cycle operating under the same condition. Please provide a complete solution
4] A Diesel engine operates on the air-standard cycle and has a displacement of3.5 liters. The engine’s compression ratio is 19, and the cutoff ratio is 2.4. The conditionsat the beginning of compression are 37 oC, 98 kPaa, and 3.7 liters. If the engine operatesat 1500 rpm, determine a) the compression ratio; b) the cycle work; and c) the powereddeveloped.
Given a Brayton cycle, with a pressure ratio equivalent to 12, as shown in the figure, determine its thermal efficiency, in %. Use Standard Cold Air Assumption Method (constant specific heats at room temperature, 25ºC).