Q2- A (0.14 m/s) oil has (density 880 kg/m & viscosity 0.026 pa.s) is pumping from first tank to second tank by using centrifugal pump and discharge pipeline 12 inch in diameter. If the pipe roughness is 0.045mm: 1- Calculate pipe frictional head loss for discharge pipe 6100m in length. 2- Calculate pump liquid power if oil level in first tank 7 m, the oil level in second tank is 14 m, and the suction pipe length is 53 m and diameter is 14 inch.

Q2- A (0.14 m/s) oil has (density 880 kg/m & viscosity 0.026 pa.s) is pumping from first tank to second tank by using centrifugal pump and discharge pipeline 12 inch in diameter. If the pipe roughness is 0.045mm: 1- Calculate pipe frictional head loss for discharge pipe 6100m in length. 2- Calculate pump liquid power if oil level in first tank 7 m, the oil level in second tank is 14 m, and the suction pipe length is 53 m and diameter is 14 inch.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

pump with critical cavitation number 0,08 pumps water to a total head of 60 m and temperature of 15°C (Pv=1707 Pa). If the barometric pressure is 98 kPa, head loss in the suction pipe is 1m. Find the maximum value of static suction lift in meters to avoid cavitation in the pump.
Pressures at the start and end of a straight horizontal pipe pumping water are measured as 2560337.6Pa and 168693.4Pa, respectively. Calculate the head loss due to friction. (Lemme Know If anything missed)
Q1: In a venturemeter used for measuring the flow ofoil (-0.85) through a horizontal pipeline, the pipe diameter is 2.4 times the diameter at the throat. Connections are made from the entrance to the meter and the throat to a vertical L tube containing mercury If the difference level between the fluids in the U - tube arms is (x +) in em, where S.N. is student serial number. Neglect friction in the pipe. Find an expression in terms of x for the velocity of the oil in the pipe.
Sunflower oil (SG = 0.7, viscosity = 154cP) is pumped at a rate of 85 ft^3/min (ID = 3.5in) from large open reservoir to the bottom of another open tank. The liquid level in the reservoir is maintained at 4.5ft, and the bottoms of the reservoir and tank are 17ft apart, vertically. Friction losses in the pipe amount to 7.5% of the elevation head. If 2 hp of power is required for the process, what is the expected liquid level in the receiving tank?
The 28-in-diameter pump in Fig. at 1170 r/min isused to pump water at 20°C through a piping system at14,000 gal/min. (a) Determine the required brake horsepower.The average friction factor is 0.018. (b) If there is65 ft of 12-in-diameter pipe upstream of the pump, how farbelow the surface should the pump inlet be placed to avoidcavitation?
1. Assume a horizontal shaft handling water at 65 deg C (Pv=2.503 KPa, Density=980.5 m3/kg). The suction nozzle is 4.35 m below the pump centerline and the pressure gauge reading at this point is 221Kpag. Determine the NPSHa if the head loss is 0.82 m. If the NPSHr is 3m less than the NPSHa you got on question number 1, determine the pump suction specific speed at pump rotating at 1800rpm and Q=500gpm
a. the total head loss due to friction (HL = hfs + hfd) in meters b. the total dynamic head in meters c. the water power in kW
A pump draws 24 li/s of water from the lower reservoir and lifts it to upper reservoir. The head lossfrom the inlet 150 mm pipe diameter is three times the velocity head and the head loss going to theoutlet 100mm pipe diameter is 25 times its velocity head. What is the power generated by the pump tothe system in horsepower. (Note: Velocities from the reservoir are different from the velocities of thepipe and pleaseee draw a diagram if you can thank you so much)
Gasoline at 38°C is being drawn from a closed tank having a pressure of 70kPag. The level of gasoline in the tank is 2.5m above the pump centerline. The suction line friction loss is 0.6m. The vapor pressure of the gasoline is 48kPa absolute and its specific gravity is 0.72. Determine the NPSH available.
1 - If the pipeline is now specified to be of Schedule 40 with a nominal diameter of 6 in., and the available pressure at the pump exit is P2 = 132.7 psig, what flow rate Q (gpm) can be expected? Answer the following additional questions: 2 -If the combination of pump and motor is 80% efficient, how much electrical power (kW) is needed to drive the pump? 3 -, in order to avoid vapour lock, the pressure in the pipeline must always be above the vapor pressure of the crude oil, what is the maximum permissible elevation of point 3 relative to point 4? 4 -If the flow in the pipeline were at the upper limit of being laminar, what pump exit pressure would then be needed? (Answer this part without using the friction factor plot.
A service truck transfers hydraulic oil with a kinematic viscosity of 200 cSt through a 2-in. I.D. hose 100 ft. long to a bulldozer at a flow rate of 50 gal/min. What is the pressure drop between the service truck and the bulldozer if the fluid Sg is 0.85?
4. Brine (SG = 1.1, viscosity = 1.1cP) is pumped at a rate of 45 ft^3/min (ID = 2.5in) from large open reservoir to the bottom of another open tank. The liquid level in the reservoir is maintained at 5.2ft, and the liquid level in the reservoir and the bottom of the discharge tank are 18ft apart, vertically. Friction losses in the pipe amount to 10% of the elevation head. If 2.15 hp of power is required for the process, what is the expected liquid level in the receiving tank?