Q2 : The three bars shown in fig are pined at point B which carry a loadP and fixed at points A, C and D. The length of the three bars AB, BDand CB is (L) . The cross section area for each bar is Aj except the barCB which has different cross section area of A, . All three bars have thesame young modulus E. Determine the axial force in cach of the bars.

given data: lenth of each bar AB=BC=BD=L cross sectional area bar(AB)=bar(BD)=A1 cross sectional…

Q2 : The three bars shown in fig are pined at point B which carry a load P and fixed at points A, C and D. The length of the three bars AB, BD and CB is (L) . The cross section area for each bar is A, except the bar CB which has different cross section area of Az . All three bars have the same young modulus E. Determine the axial force in each of the bars.

Q2 : The three bars shown in fig are pined at point B which carry a load P and fixed at points A, C and D. The length of the three bars AB, BD and CB is (L) . The cross section area for each bar is A, except the bar CB which has different cross section area of Az . All three bars have the same young modulus E. Determine the axial force in each of the bars.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.189RP: The tongs shown are designed for lifting blocks of ice. If the weight of the ice block is W, find...

See similar textbooks

Similar questions

Find the magnitude of the pin reaction at B caused by the weight W=80lb. Neglect the weights of the members.
The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016, determine the force F required to advance the bar at a constant speed.
The tongs shown are designed for lifting blocks of ice. If the weight of the ice block is W, find the horizontal force between the tongs and the ice block at C and D. Neglect the weights of the tongs.
The simplest truss consists of two rods and is loaded by the block. Given: block weight Q = 2,2 kN. Angle α = 39 degrees. Find: the algebraic (positive or negative) value (in kN) of normal force N2 in the rod 2, considering that N2>0 for tension and N2<0 for compression.
A uniform bar 3.00 m long is held by ropes at the ends making angle 60.0 and 30.0,respectively, with the horizontal. A weight of 200 N is hung 0.500 m from the leftend where the 60.0 rope is attached. Find the tension in the ropes (T1 & T2) andthe weight (W) of the bar
A bucket, weighing 375 N, is hung from strings CAD, BA and EA, as shown in the image. Determine the tension of the CAD rope.
The small piston of a hydraulic press has a cross-sectional area of 3cm2, and its larger piston has a cross-sectional area of 200cm2. What downward force must be applied to the small piston for the lift to raise a load of 15KN?
The quarter circle gate BC in Fig. is hinged at C.Find the horizontal force P required to hold the gatestationary. Neglect the weight of the gate.
The pulleys are frictionless and of negligible weight, find Tension (N) in the cord supporting block C?
The 400-kg precast concrete section is hoisted by a vertical force 'T' from a crane. Find the tension in cables AB, AC, AD.
When a motor is set on a pivoted mount seen below, its weight can be used to maintain tension in the drive belt. When the motor is not running the tensions T1 and T2 are equal. The total mass of the platform and the motor is 100.0 kg, and the diameter of the drive belt pulley is 16.0 cm. when the motor is off, find: (a) the tension in the belt, and (b) the force at the hinged platform support at point C. Assume that the center of mass of the motor plus platform is at the center of the motor.
In a hydraulic press, the small cylinder has the diameter of 8 cm while the larger piston has thediameter of 22 cm. If the force of 600 N is applied to the small piston, what is the force on thelarger piston, neglecting friction?