Draw the circuit diagram of DC power supply of 12 V output by using Full wave rectifier center tap rectifier, filter, Zener diode and any load. Simulate the circuit by using suitable simulation tools. [Expected to include circuit diagram, screen shot of simulations, working of the circuit in detail and write your reflection on the circuit].

Draw the circuit diagram of DC power supply of 12 V output by using Full wave rectifier center tap rectifier, filter, Zener diode and any load. Simulate the circuit by using suitable simulation tools. [Expected to include circuit diagram, screen shot of simulations, working of the circuit in detail and write your reflection on the circuit].

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter30: Dc Motors

Section: Chapter Questions

Problem 6RQ: What is CEMF?

See similar textbooks

Similar questions

Design rectifier circuits to provide an output of100 VDC using a half wave rectifiercalculate the transformer peakvoltage rating, the diode PIV ratings, and thetransformer turns ratio, if power is taken fromthe 220V line ac supply.
Design Half-wave Rectifier Circuit to provide an output of 100 VDC. Then calculate its transformer peak voltage rating, the diode PIV rating, and the transformer turns ratio, if the power is taken from the 220V line AC supply
Derive the equation of the Vdc, Vrms, Efficiency, RF, and TUF of a given three-phase half-wave rectifier circuit shown. Draw the output waveform of the pulsating DC voltage neatly and accurately.
Create a schematic diagram for building an AC-DC power supply that uses a complete bridge rectifier, filter capacitors, and regulators and has a selectable output voltage. Keep in mind: When a load is attached, the power supply must be able to deliver at least 500mA of output current.
27. For the given Full-Wave Bridge Rectifier circuit below with capacitor filter, it produces a ripple voltage waveform shown. If V2 is given as 14 volts and V1 is given as 8 volts, compute for the ripple peak-to-peak voltage, dc voltage and ripple factor. If the load resistance has a value of 9 kiloohms, how much should be the dc current?. compute for the peak output voltage at the output of the rectifier. If silicon diodes are used, what is the value of the secondary peak voltage?. If N1 is given as 1300 and N2 is given as 600, compute for the primary peak voltage. 4. The value of dc current (Idc) in amperes is ? 5. The value of the output peak voltage (Vpout) in volts is ? 6. The value of peak secondary voltage (Vpsec) in volts is ? 7. The value of primary peak voltage is (Vppri) in volts is ?
27. For the given Full-Wave Bridge Rectifier circuit below with capacitor filter, it produces a ripple voltage waveform shown. If V2 is given as 14 volts and V1 is given as 8 volts, compute for the ripple peak-to-peak voltage, dc voltage and ripple factor. If the load resistance has a value of 9 kiloohms, how much should be the dc current?. compute for the peak output voltage at the output of the rectifier. If silicon diodes are used, what is the value of the secondary peak voltage?. If N1 is given as 1300 and N2 is given as 600, compute for the primary peak voltage. 1. The value of the ripple peak-to-peak voltage (Vrpp) in volts is ? 2. The value of the dc voltage (Vdc) in volts is ? 3. The value of the ripple factor is ?
For the given Full-Wave Bridge Rectifier circuit below with capacitor filter, it produces a ripple voltage waveform shown. If V2 is given as 14 volts and V1 is given as 6 volts, compute for the ripple peak-to-peak voltage, dc voltage and ripple factor. If the load resistance has a value of 5 kiloohms, how much should be the dc current?. compute for the peak output voltage at the output of the rectifier. If silicon diodes are used, what is the value of the secondary peak voltage?. If N1 is given as 1400 and N2 is given as 500, compute for the primary peak voltage.
A 10 V Zener diode is used to regulate the voltage across a variable loadresistor. The input voltage Vs varies between 13 and16 V. The loadcurrent (??) varies between 10 and 85 mA. The minimum Zener current is15 mA. Findi. The maximum value of Rsii. The maximum power dissipated by the Zener diode, using the value ofRs.
For the given Full-Wave Bridge Rectifier circuit below with capacitor filter, it produces a ripple voltage waveform shown. If V2 is given as 18 volts and V1 is given as 6 volts, compute for the ripple peak-to-peak voltage, dc voltage and ripple factor. If the load resistance has a value of 6 kiloohms, how much should be the dc current?. compute for the peak output voltage at the output of the rectifier. If silicon diodes are used, what is the value of the secondary peak voltage?. If N1 is given as 1100 and N2 is given as 600, compute for the primary peak voltage. 1. The value of the ripple peak-to-peak voltage (Vrpp) in volts is..... 2. The value of the dc voltage (Vdc) in volts is..... 3. The value of the ripple factor is..... 4. The value of dc current (ldc) in amperes is..... 5. The value of the output peak voltage (Vpout) in volts is..... 6. The value of peak secondary voltage (Vpsec) in volts is..... 7. The value of primary peak voltage is (Vppri) in volts is.....
Determine the peak output voltage for the bridge rectifier in this figure. Assuming the practical model, what PIV rating is required for the diode? The transformer is specified to have a 12 Vrms secondary voltage for the standard 110 V across the primary.
The circuit shown below is to be used to provide a stabilised output to the load. The Zener diode characteristic is also shown on the next page. Find the load voltage (VL) and source current (IS) if the battery voltage is 18 V, series resistance is 1.4 KΩ and load resistance is 11 KΩ. Additionally, determine the value of the source resistance (R) if the Zener diode is at the threshold of activating in its reverse bias. Comment on the purpose of having this value of R in the circuit.
A single-phase fully controlled, full-wave, bridge rectifier has a source of 220 V rms at 50 Hz, and is feeding a load 15 Ω and 10 mH. The firing angle α = 60˚ and the current extinction angle β =250˚; Determine (a) Average load voltage and current (b) RMS load voltage and current (c) AC and DC powers absorbed by the load (d) Determine the efficiency of the converter (e) Sketch the appropriate load voltage and load current waveforms (f) Determine whether the current is continuous or discontinuous