Q3) The half-wave rectifier shown below is operating at a frequency of 60 Hz, and the rms value of the transformer voltage is 6.3 V. (a) What is the value of the dc output voltage, VO, if the diode voltage drop Von = 1 V and assuming that R = 0? (b) What is the minimum value of C required to ensure that the ripple voltage is less than 0.25 V if R = 50 O? %3D DI R vo

Q3) The half-wave rectifier shown below is operating at a frequency of 60 Hz, and the rms value of the transformer voltage is 6.3 V. (a) What is the value of the dc output voltage, VO, if the diode voltage drop Von = 1 V and assuming that R = 0? (b) What is the minimum value of C required to ensure that the ripple voltage is less than 0.25 V if R = 50 O? %3D DI R vo

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is CEMF?
What is the difference between a diode and rectifier?
The full-wave rectiﬁer ias shown is operating at a frequency of 60 Hz, and the rms value of the transformer output voltage is 18 V. (a) What is the value of the dc output voltage if the diode voltage drop is 1 V? (b) What is the minimum value of C required to maintain the ripple voltage to less than 0.25 V if R = 0.5 Ω? (c) What is the PIV rating of the diode in this circuit? (d) What is the surge current when power is ﬁrst applied? (e) What is the amplitude of the repetitive current in the diode?
Design a center-tapped full-wave Rectifier Circuit to provide an output of 100 VDC. Then calculate its transformer peak voltage rating, the diode PIV rating, and the transformer turns ratio, if the power is taken from the 220V line AC supply
Design Half-wave Rectifier Circuit to provide an output of 100 VDC. Then calculate its transformer peak voltage rating, the diode PIV rating, and the transformer turns ratio, if the power is taken from the 220V line AC supply
Consider the full-wave rectifier circuit shown below, where• vS(t) is a sinusoidal signal with a peak value (Vs = 5 V).• Diodes are modelled using constant voltage model with VDO = 0.7 V• The ac line voltage has an rms value of 120 V and a frequency (f) = 60 Hza) Calculate the transformer turns ratio. b) Plot in the same graph signal vS(t) and the output signal vO(t) versus time (t) (show all details including amplitudes, time instances, etc.) c) Calculate the rms value of the output signal vO(t). (hint: sin2(x) = 0.5(1- cos(2x))) d) If a capacitor C=3.58 F is connected across R = 10 k, repeat (b) in a new graph
Design rectifier circuits to provide an output of100 VDC using a half wave rectifiercalculate the transformer peakvoltage rating, the diode PIV ratings, and thetransformer turns ratio, if power is taken fromthe 220V line ac supply.
During output power measurement DC gives a deflection whereas AC gives properoutput. Why? Explain it. (Voltmeter, Ammeter and Isolator Connection of a Simple Half Wave Rectifier Circuit.)
For the Zener regulated power supply a shown, the rms value of vI is 15V, the operating frequency is 60Hz, R =100Ω, C =1000μF, the on voltage of diodes D1 and D2 is 0.75V, and the Zener voltage of diode D3 is 15V.(a)What type of rectiﬁer is used in this power supply circuit?(b) What is the dc voltage at V1? (c) What is the dc output voltage VO?(d)What is the magnitude of the ripple voltage at V1? (e) What is the minimum PIV rating for the rectiﬁer diodes? (f) Draw a new version of the circuit that will produce an output voltage of−15 V.
A schematic design of a full-wave bridge type power supply is given below. Provide the appropriate values for the inductors, diodes, capacitor and resistors, such that the output DC voltage is 6.2 V and the max. output power for the load resistance is 20 mW (percentage error for output voltage and output power is 2%). AC voltage source: Amplitude=311.13, Freq=60, DC offset= 0. For the rectifier part, choose diodes with an appropriate PIV rating. Show all the formulas and computations involved in acquiring the values for the inductors, diodes, capacitor and resistors. In choosing your Zener diode, consider the output voltage and the output current. Note that the output current should be the minimum Zener current. For the value of the series resistor RS, choose a lower value for less ripple but always consider the required output voltage. The ripple voltage peak-to-peak value should be less than or equal to 1% of the required output voltage. Use the formula below for choosing the value…
Design rectifier circuits to provide an output of100 VDC using a.) HWR b.) Center-tappedFWR and c.) Bridge-Type FWR circuits. For each circuit, calculate the transformer peakvoltage rating, the diode PIV ratings, and thetransformer turns ratio, if power is taken fromthe 220V line ac supply