Q3/ The A-36 steel axle is made from tubes AB and CD and a solid section BC. It is supported on smooth bearings that allow it to rotate freely. If the gears, fixed to its ends, are subjected to 85 N.m torques, determine the angle of twist of gear A relative to gear D. The tubes have an outer diameter of 35 mm and an inner diameter of 25 mm. The solid section has a diameter of 45 mm. 400 mm 85 N-m 400 mm 85 N-m

Q3/ The A-36 steel axle is made from tubes AB and CD and a solid section BC. It is supported on smooth bearings that allow it to rotate freely. If the gears, fixed to its ends, are subjected to 85 N.m torques, determine the angle of twist of gear A relative to gear D. The tubes have an outer diameter of 35 mm and an inner diameter of 25 mm. The solid section has a diameter of 45 mm. 400 mm 85 N-m 400 mm 85 N-m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The shafts are made of steel with shear modulus of 75 GPa. Determine the angle of twist of gear B if a torque of 30 kN·m is applied to gear B. Both shafts have the same diameter of 90 mm. (Hint: for the meshing cylindrical gears, i.e. gear C and D, the angle of twist need to time the radius of the gear while applying the equation of compatibility.)
A pair of 20º full depth involute teeth bevel gears connect two shafts at right angles having velocity ratio 3 : 1. The gear is made of cast iron having allowable static stress as 70 MPa and the 20teeth pinion is of steel with allowable static stress as 100 MPa and 200BHN. The pinion works at 750 r.p.m. Determine the maximum power can be transmitted by the gears if the module is 10mm. Kf=1.4
The motor produces a torque of T = 20 N # m on gear A. If gear C is suddenly locked so it does not turn, yet B can freely turn, determine the angle of twist of F with respect to E and F with respect to D of the L2-steel shaft, which hasan inner diameter of 30 mm and an outer diameter of 50 mm. Also, calculate the absolute maximum shear stress in the shaft. The shaft is supported on journal bearings at G at H.
Q: Determine the angle of twist of end B with respect to end A. Given: The splined ends and gears attached to the A992 steel shaft are subjected to the torques shown where T=210 N⋅mT=210 N⋅m. The shaft has a diameter of 45 mm. Note: Attached in the picture is a list of wrong answers (including one from Bartleby) and im at wits end :)
The composite shaft below, consists of three sections, a tubular indication welded, through flanges Aand B, two 1” diameter bars. Neglect the thickness of the flanges and determine the angle of twist of the endC from shaft to end D. Shaft 0 is relative to a torque of lb × ft. The A-36 material.
The A-36 steel assembly consists of a tube having an outer radius of 1 inch and a wall thickness of 0.125 inch. Using a rigid plate at B, it is connected to the solid 1-inch diameter shaft AB. Determine the rotation of the tube’s end C if a torque of 200lb inches is applied to the tube at this end. The end A of the shaft is fixed supported.
The shaft is made of A-36 steel. It has a diameter of 1 in. and is supported by bearings at A and D, which allow free rotation. Determine the angle of twist of gear C with respect to B.
The splined ends and gears attached to the A992 steel shaft are subjected to the torques. The shaft has a diameter of 50 mm Determine the angle of twist of end B with respect to end A.
A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has4 wheels of the same diameter of 400 mm and drives at a gear ratio of 5 to 1 ifits gearbox 5th gear is selected. The gear’s teeth are of involute form with amodule of 8 mm, an addendum is double the module, and the pressure angle isequal to 20° .1.1. If the driving shaft of the front wheels of the truck is connected to the output shaftof the gearbox, determine the number of teeth on the pinion to avoid interferenceand the corresponding number of teeth on the gear wheel.
The approximate distance between the two parallel shafts is 1500 mm. The shafts are to be connected by spur gearing. If one shaft runs at 1500 r.p.m. and the other at 2500 r.p.m., Design the gears, if the module is 7 mm. (
TORSION An aluminum shaft with a constant diameter of 70 mm is loaded by torques applied to gears attached to it. Use G = 28 GPa. DETERMINE: A. the relative angle of twist of gear D relative to gear A (in degrees) B. the direction of the rotation of A relative to D? PROVIDE FBD
Two cqual involute gear wheels of 40 teeth each, 3 mm module and 20° pressures angleare in mesh. Determine the minimum addendum if 2 pairs of teeth are always in mesh.The gear wheels rotate at 750 r.p.m. and transmit 4.6 kW. Find the normal force at eachpair assuming equal direction of load between the pairs. Neglect friction.