Q4) A 2-wire d.c. distributor cable AB is 2 km long and suppliesloads of 100A,150A,200A and 50A situated 500 m, 1000 m, 1600m and 2000 m Trom the feeding point A. Each conductor has aresistance of 0-01 2 per 1000 m. Calculate the voltage at eachload point if a voltage of 300 V is maintained at point A.

Answered: Image /qna-images/answer/933d9b14-6324-4932-aa77-30503109cf7e.jpg

Q4) A 2-wire d.c. distributor cable AB is 2 km long and supplies loads of 100A,150A,200A and 50A situated 500 m, 1000 m, 1600 m and 2000 m from the feeding point A. Each conductor has a resistance of 0-01 2 per 1000 m. Calculate the voltage at each load point if a voltage of 300 V is maintained at point A.

Q4) A 2-wire d.c. distributor cable AB is 2 km long and supplies loads of 100A,150A,200A and 50A situated 500 m, 1000 m, 1600 m and 2000 m from the feeding point A. Each conductor has a resistance of 0-01 2 per 1000 m. Calculate the voltage at each load point if a voltage of 300 V is maintained at point A.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.1P: The Aluminum Electrical Conductor Handbook lists a dc resistance of 0.01558 ohm per 1000 ft at 20C...

See similar textbooks

Similar questions

Determine the GMR of each of the unconventional stranded conductors shown in Figure 4.30. All strands have the same radius r.
. A two conductor main A B, 500 m in length is fed from both ends at 250 volts. Loads of 50 A, 60 A, 40A and 30 A are tapped at distance of 100 m, 250 m, 350 m and 400 m from end A respectively. If the X-section of conductor be 1 cm2and specific resistance of the material of the conductor is 1·7 µ Ω cm,determine the minimum consumer voltage.
A two wire DC distributor AB, 1000 meter long, is supplied from both ends, 240 V at A and 242 V at B. There is a concentrated load of 200 A at a distance of 400 meter from A and a uniformly load 1.0 A/m between the midpoint and end B. Determine (i) the current fed at points A and B (ii) the point of minimum potential and (iii) voltage and this point. Consider cable resistance as 0.005 ohm per 1000 meter each core.
5. A 2-wire DC ring distributor is 375m long and is fed with 300V at point A. At point B, 200m from A, load of 150A is taken and at point C, 100m in the opposite direction, a load of 100A is taken. If the resistance per 100m of single conductor is 0.03, find: i. Current in each section of distributor ii. Voltage at points B and C iii. Point of minimum potential
A 2-wire d.c. distributor cable AB is 3 km long and supplies loads of 100A, 150A,200A and 50A situated 600 m, 1000 m, 1500 m and 2000 m from the feeding point A. Each conductor has a resistance of 0.02 ohm per 1000 m. Calculate the p.d. at each load point if a p.d. of 350 V is maintained at point A.
Write any four methods of voltage control and Draw the basic block diagram of AC – DC transmission system. and A transmission line has a span of length 250 m and the weight of the conductor per metrelength is 0.63 Kg. The tension in the conductor is 1250 Kg. Calculate the sag and heightabove the ground at which the conductor should be supported. Consider the groundclearance required is 13m
On the 1km long dc distributor above the applied voltage at point O is 200V. Lengths ??? = 100?,??? = 600? and the impedance for the conductor material per 10000m is ?? = 5 < 53.130Ω. Calculate:a. The potential at point C b. Current along section OC of the distributor
A 415 single core cable has a conductor diameter of 0.5 cm and a sheath of inside diameter 3 cm. In cable insulation, find: (i) minimum stress (in V/cm); (ii) maximum stress in (V/cm); (iii) Describe where these minimum and maximum stress will occur in cable insulation?; (iv) Suggest what should be the minimum dielectric strength (in V/mm) of the cable insulation to avoid any breakdown of the given cable
How the expression for the lowest point of the catenary curve if the supports are at different levels is obtained? Given that weight of conductor = 0.35 kg/m, maximum allowable strength= 800kg, span length =160m, safety factor = 2, find the minimum point of catenary if supports are at 70m and 65m.
A three phase, 11 KV, underground cable system, consider a single core of conductor radius 0.5 cm diameter and lead sheath of 1.25 cm. The core and lead sheath have been separated by two intersheaths with radius 0.75 cm and 1 cm. Draw the cable core, dielectric and intersheath layers showing the thickness of each layer, then determine the voltages on the both intersheaths. Suppose the maximum stress on the layers are the same.
A 2-wire d.c. distributor cable AB is 2 km long and supplies loads of100A, 150A,200A and 50A situated 500 m, 1000 m, 1600 m and 2000 m from the feeding point A. Each conductor has a resistance of 0•01 Ω per 1000 m and 300 V is maintained at point A. Calculate the resistance between point EB. *
A three phase, 33 KV, underground cable system, consider a single core of conductor radius 0.8 cm diameter and lead sheath of 2.3 cm. The core and lead sheath have been separated by two intersheaths with radius 1.3 cm and 1.8 cm. Draw the cable core, dielectric and intersheath layers showing the thickness of each layer, then determine the voltages on the both intersheaths. Suppose the maximum stress on the layers are the same. Please i need it know please