Q5. A force of 1500 KN is applied on a steel bar, young's modulus is 200 G Pa. Length of the bar is 5000 mm andradius is 100 mm. Calculate the clastic strain energy due to the applied load.Marks (15)CLO3- C4 (Analysis) - PLO2 (Problem Analysis)BC

Answered: Image /qna-images/answer/a6255c35-197b-49c0-b20d-f8e77dcbd282.jpg

Q5.A force of 1500 KN is applicd on a stcel bar, young's modulus is 200 G Pa. Length of the bar is 5000 mm and radius is 100 mm. Calculate the elastic strain energy duc to the applied load. Marks (15) CLO3- C4 (Analysis) - PLO2 (Problem Analysis) L B C

Q5.A force of 1500 KN is applicd on a stcel bar, young's modulus is 200 G Pa. Length of the bar is 5000 mm and radius is 100 mm. Calculate the elastic strain energy duc to the applied load. Marks (15) CLO3- C4 (Analysis) - PLO2 (Problem Analysis) L B C

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.7P: (a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the...

See similar textbooks

Related questions

Q: A laminated spring 1 m long is made up of plates, each 5 cm wide and 1 cm thick. If the bending…

A: We know that a 1 m long laminated spring is made up of plates that are each 5 cm broad and 1 cm…

Q: When a beam 6 m long with a cross-sectional area of 19.4 cm2 is subjected to a compression…

A: Given dataL=6mA=19.4cm2F=16x104NS=4.5mmTo find young's modulus

Q: A circular pipe of internal diameter 30 mm and thickness 4 mm is subjected to a force 30 kN and the…

Q: Figure 6(a) shows an example of pressure vessel with radius ofr, and yield stress O. Suppose the…

A: Calculated the minimum thickness to sustain the pressure vessel according to the von mises yield…

Q: Q3/ The below figure illustrates the cross section of a column and its bracing details for both its…

Q: When a round bar material with diameter of 37.5 mm, length of 2.4 m, Young's mod of 110 GN/m² and…

A: Given data:Young modulus of elasticity=110 GN/m2Bar diameter=37.5 mmShear modulus=42 GN/m2Bar…

Q: For a rigid cylindrical steel rod of 2m length 2 cm diameter and yield stress fy = 470 MPa,…

A: Given datalength=2mdiameter= 2 cmyeild stress fy=470 MpaTo determine axial force to yield the rod

Q: A drill drills a hole in a leg of a furniture. Uses a hand-operated drill with a bit of diameter…

A: Given Data Diameter of drill bit is : d=5.79 mm=5.79×10-3 m Resisting torque is : T=0.36 N·m…

Q: If Young's modulus of some material is 150 GPa and shear modulus is 50 GPa, find the poisson's ratio…

A: Given, Young's modulus = E = 150 GPa Shear modulus = G = 50 GPa Let us consider, Poisson's ratio…

Q: A bar having two cross sectional areas is loaded by an axial force (P). Part AB and BC are circular…

Q: Find the final length of the bar of an aluminum alloy with a modulus of elasticity of 68.8 GPa,…

Q: A cantilever of circular cross section has a diameter of 150 mm and is made from steel, which, when…

Q: At a point in a given material the three dimensional state stress is given by ox = oy = oz = 10 MPa…

Q: A 1m long steel bar (E=200GPa) of 10mmx10mm dimension fixed at both ends is heated to 90°C from…

Q: A rubber block with dimensions of 120x120x120 mm is compressed in a rigid mold cavity with a…

Q: A steel hoop, 10 mm thick and 80 mm wide, with inside diameter 1500.0 mm, is heated and shrunk onto…

Q: As shown, there is a gap between the aluminum bar and the rigid slab that is supported by two copper…

Q: A rubber block with dimensions of 120x120x120 mm is compressed in a rigid mold cavity with a…

Q: Q4.A cantilever beam, 50 mm wide by 150 mm high and 6 m long, carries a load that varies uniformly…

A: Flexural stress would be maximum at the fixed support end.

Q: block is 4 inches long in the x direction, 2 inches long in the y direction, and 3 inches long in…

Q: A rubber block with dimensions 120x120x120 mm is a rigid mold It is compressed with a vertical force…

A: Given data: The dimensions of the rubber block are 120 mm×120 mm×120 mm. The vertical force acting…

Q: A steel circular tube is subjected to torsion by torques T applied at the ends as shown below. The…

A: This problem is related to the torsion of the shaft. torsion, when the twisting moment is applied to…

Q: What is the Poisson's ratio if the ratio of Young's modulus (E) to the shear modulus (G) is 2?

A: Given data, The ratio of young's modulus and shear modulus is 2 ie E/G=2

Q: A 8mm diameter rod, of unknown material, is subjected to 50kN tensile load. In the process, its…

A: GIVEN DATA Diameter d=8mm Load P=50KN Initial length =300mm final length = 303mm

Q: Imagine that a long steel wire hangs vertically from a high-altitude balloon.(a) What is the…

Q: A cross-sectioned rod (5*5cm) was subjected to a compressino force (F=500 103 N), so the resulting…

Q: A one mm diameter steel wire is wounded around a copper tube with external and internal diameters of…

A: Given: The diameter of wore, d = 1 mm The external diameter of tube, Do = 140 mm The internal…

Q: A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented…

A: Given ∆LAC=0.72mmE=223 MPa=223 N/m2=223 ×10-4 N/cm2H1=LAB=7 cmH2=LBC=10 cmArea of bar AB=AAB=2×2=4…

Q: A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented…

Q: In constructing a large mobile, Jude hangs an aluminum sphere of mass 6.0kg from a vertical steel…

Q: Simple Stress and Strain Question 2 At short, reinforced cement concrete column 600 mm x 600 mm has…

A: To find: The stress in steel, concrete and elastic shorting of the column. Given: The size of the…

Q: A 30 cm X 16 cm rolled steel joist of I-section has flanges 11 mm thick and web 8 mm thick. Find the…

A: Given that, I-section,Width of flange=30 cmHeight of web=16 cm,Thickness of flange=11 mm,Thickness…

Q: A bar of triangular cross section with base 15mm carries a load of 100 kN. Calculate its minimum…

Q: A rigid beam of negligible weight is supported in a horizontal position by 2 rods made of steel and…

Q: A 1 m length bar of square cross section with side length 2cm, . is fully supported at one end and…

Q: W 3 M M

A: Assumption: - The bone is considered to be a cantilever beam of the hollow section. The weight of…

Q: A wire 4m long is stretched horizontally between points A and B 4m apart. A load W placed at the…

A: Given data Length of the Stretched wire = 4 mArea of cross-section of wire = 25 mm2Young's Modulus =…

Q: 7. A wooden storage vat is 6 m in diameter and is filled with 7 m of oil, s = 0.8. the wood staves…

Q: A bronze tire (thickness=12mm, width= 110 mm, internal diameter=800 mm) was heated and shrunk onto…

Q: A thin steel cylinder 1.3 m long is subjected to internal pressure; the change in volume owing to…

A: When pressure is applied to a pipe, hoop stress occurs along its circumference. The axial direction…

Q: Problem #7: For the structure below find the maximum absolute vertical shear stress (Oxy) anywhere,…

A: Draw the F.B.D of the given beam and calculate the reactions. For the equilibrium of the given…

Q: A cylindrical assembly consisting of a brasscore and an aluminum collar is compressed by a loadP…

A: (a) Calculate the cross-section area of the aluminum collar from the given figure. A1=π440 mm2-25…

Q: For a given material, Young’s modulus is 100GPa and shear modulus is 40GPa. Find the bulk modulus…

Q: A steel pipe having a length of 2 m, an outside diameter of 0.2 m and a wall thickness of 10 mm, is…

Q: A bronze sleeve is slipped over a steel bolt and held in place by a nut that is turned to produce an…

Q: Three different materials, designed A, B and C are tested in tension using test specimens having…

Q: A bar is subjected to fluctuating tensile load from 20 KN to 100 kN. The material has yield strength…

A: Given, Minimum force during a cycle = Fmin = 20 kN Maximum force during a cycle = Fmax = 100 kN…

Q: A solid circular bar of steel (G = 78 GPa)transmits a torque T = 360 N ? m. The allowablestresses in…

Q: A bronze sleeve is slipped over a steel bolt and held in place by a nut that is turned to produce an…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

Q5. A force of 1500 KN is applied on a steel bar, young's modulus is 200 G Pa. Length of the bar is 5000 mm and
radius is 100 mm. Calculate the clastic strain energy due to the applied load.
Marks (15)
CLO3- C4 (Analysis) - PLO2 (Problem Analysis)
B
C

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For a given material, Young’s modulus is 100GPa and shear modulus is 40GPa. Find the bulk modulus and lateral contraction of a round bar of 40mm diameter and 2.5 m long when stretched 2.5 mm.
An elastic rubber sphere of radius 20mm is pressed upon a rigid sphere of radius 50mm. The Young’s modulus of rubber is 0.1GPa and the Poisson’s ratio is 0.45. If the maximum allowable pressure below the indenter is 10MPa, determine the maximum contact force that we can apply and the corresponding contact radius.
A rectangular steel block is 300mm in the x direction, 200mm in the y direction and 150mm in the z direction. The block is subjected to a triaxial loading consisting of three uniformly distributed forces as follows: 250kN tension in the x direction, 320kN compression in the y direction and 180kN tension in the z direction. For steel, v=0.30 and E=200,000MPa. Determine the total strain in the x direction due to the forces applied in the three directions.
What is the Poisson's ratio if the ratio of Young's modulus (E) to the shear modulus (G) is 2?
A specimen of titanium alloy is tested in torsion and the shear stress–strain diagram is shown in Fig.a. Determine the shear modulus G, the proportional limit, and the ultimate shear stress. Also, determine the maximum distance d that the top of a block of this material, shown in Fig. b, could be displaced horizontally if the material behaves elastically when acted upon by a shear force V. What is the magnitude of V necessary to cause this displacement?
A wood stave pipe, 120 cm in inside diameter, is to resist a maximum water pressure of 1,200 kPa. If the staves are bound by steel flat bands (10 cm by 2.50 cm), find the spacing of the bands if its allowable stress is 105 MPa.\ Please explain the steps and formulas used.
Steel railroad reels 15 m long are laid with at an initial temperature Ti = 46 °C. Assume α = 11.7 μm/(m·°C) and E = 200 GPa. What stress would be induced in the rails in MPa at a final temperature of Tf = 107 °C, if there were no initial clearance?
A rectangular bar is notched on two sides as shown in Fig. 5.9a. The dimensions of the bar are thickness t = 0.2 cm, D = 2 cm, d = 1.8 cm, h = 0.1 cm, and r = 0.15 cm. If an elastic load of 15 kN is applied along the axis of the bar, what is the maximum stress in the vicinity of the notches? If the yield strength of the material is 950 MPa, will the material yield near the notches under this load?
1. A solid piece of metal of volume 10,000 mm3 is compressed by a pressure of 70 MPa. Determine the bulk modulus given that the Young’s modulus E is 214 Gpa and the Poisson’s ratio is 0.33. Also determine the change in the volume.2. Starting from the first principles derive the relation between Young’s modulus (E), shear modulus (G) and Poisson’s ratio (υ)
How many coins will it take to break a chocolate if its thickness is 3cm, length 15 cm and width of 4.5 cm and flexural stress is established at 5kPa and each coin uniformly weighs 2.00 g?
A rectangular steel block is 3 inches long in the x direction, 2 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loding if three uniformly distributed forces as follows: 48 kips tension in the x direction, 60 kips compression in the y direction, and 54 kips tension in z direction. If v=0.30 and E=29x10^6 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading. DetermineNormal strain in x, y & z direction.Elongation in x, y & z direction.
A solid cylindrical rod 12 mm in diameter and 50 mm in length is attached to a rigid support at one end and twisted at its free end by 14°. If the Poisson’s ratio for this isotropic material is 0.34 and Young’s modulus is 70 GPa, what is the maximum shear stress induced?