I need the answer quickly Q6 A phase-controlled six-pulse rectifier is fed from a 460-V, 60-Hz line, suppliesan RLE load, of 0.30 and 1.7mH.When E=520, determine the feasible range of the firing angle, af.When af =60°, determine the maximum E that maintains continuous load current.Calculate the output average voltage (Vo,dc) and current (lo,dc) when the rectifieris operated with the firing angle of 60° and E=250V.

Given :Vm=460 Vf=60 HzR=0.3 ΩL=1.7 mH

Answered: Q6 A phase-controlled six-pulse…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A schematic design of a full-wave bridge type power supply is given below. Provide the appropriate values for the inductors, diodes, capacitor and resistors, such that the output DC voltage is 6.2 V and the max. output power for the load resistance is 20 mW (percentage error for output voltage and output power is 2%). AC voltage source: Amplitude=311.13, Freq=60, DC offset= 0. For the rectifier part, choose diodes with an appropriate PIV rating. Show all the formulas and computations involved in acquiring the values for the inductors, diodes, capacitor and resistors. In choosing your Zener diode, consider the output voltage and the output current. Note that the output current should be the minimum Zener current. For the value of the series resistor RS, choose a lower value for less ripple but always consider the required output voltage. The ripple voltage peak-to-peak value should be less than or equal to 1% of the required output voltage. Use the formula below for choosing the value…
A 60-Hz full-wave rectiﬁer is built with a transformer having an rms secondary voltage of 20 V and ﬁlter capacitance C =150,000 μF. What is the largest current that can be supplied by the rectiﬁer circuit if the ripple must be less than 0.3 V?
. What value of filter capacitor is required to produce a 1% ripple factor for a full-wave rectifier havinga load resistance of 1.5 kΩ? Assume the rectifier produces a peak output of 18 V.
Suppose a power supply is energized by an AC source of 119 V RMS. The transformer step-down ratio is 8:1, it uses a full-wave bridge rectifier circuit with silicon diodes, and the filter is nothing but a single electrolytic capacitor. Calculate the unloaded DC output voltage for this supply (assume 0.7 volts drop across each diode). Also, write an equation solving for DC output voltage (Vout), given all these parameters.
A basic regulator has an 8.5V zener diode of 0.5 W power and a filter voltage of 32VDC, determine the following electrical parameters: a. Calculate the minimum zener current. b. For a flexible design the diode work at 45%, what is the test current of the zener diode? c. If the load current is 10mA, what is the value of the limiting resistor connected between the zener and the filter?
A single-phase fully controlled, full-wave, bridge rectifier has a source of 220 V rms at 50 Hz, and is feeding a load 15 Ω and 10 mH. The firing angle α = 60˚ and the current extinction angle β =250˚; Determine (a) Average load voltage and current (b) RMS load voltage and current (c) AC and DC powers absorbed by the load (d) Determine the efficiency of the converter (e) Sketch the appropriate load voltage and load current waveforms (f) Determine whether the current is continuous or discontinuous
For the Zener regulated power supply a shown, the rms value of vI is 15V, the operating frequency is 60Hz, R =100Ω, C =1000μF, the on voltage of diodes D1 and D2 is 0.75V, and the Zener voltage of diode D3 is 15V.(a)What type of rectiﬁer is used in this power supply circuit?(b) What is the dc voltage at V1? (c) What is the dc output voltage VO?(d)What is the magnitude of the ripple voltage at V1? (e) What is the minimum PIV rating for the rectiﬁer diodes? (f) Draw a new version of the circuit that will produce an output voltage of−15 V.
Consider the full-wave rectifier circuit shown below, where• vS(t) is a sinusoidal signal with a peak value (Vs = 5 V).• Diodes are modelled using constant voltage model with VDO = 0.7 V• The ac line voltage has an rms value of 120 V and a frequency (f) = 60 Hza) Calculate the transformer turns ratio. b) Plot in the same graph signal vS(t) and the output signal vO(t) versus time (t) (show all details including amplitudes, time instances, etc.) c) Calculate the rms value of the output signal vO(t). (hint: sin2(x) = 0.5(1- cos(2x))) d) If a capacitor C=3.58 F is connected across R = 10 k, repeat (b) in a new graph
A 3.3-V, 30-A dc power supply is to be designed with a ripple of less than1.5percent. Assume that a half-wave rectiﬁer circuit (60 Hz) with a capacitor ﬁlter is used. (a) What is the size of the ﬁlter capacitor C? (b)What is the PIV rating for the diode? (c)What is the rms value of the transformer voltage needed for the rectiﬁer?(d) What is the value of the peak repetitive diode current in the diode? (e) What is the surge current at t =0+?
4- What is the effect of adding capacitor in parallel to the load at the rectifier output? Note: Please do not handwriting and write the answer briefly
A 2500-V, 2-A, dc power supply is to be designed with a ripple voltage ≤ 0.5 percent. Assume that a half-wave rectiﬁer circuit (60 Hz) with a capacitor ﬁlter is used. (a) What is the size of the ﬁlter capacitor C? (b) What is the minimum PIV rating for the diode? (c) What is the rms value of the transformer voltage needed for the rectiﬁer? (d) What is the peak value of the repetitive current in the diode? (e) What is the surge current at t =0+?
Consider a three-phase diode rectifier supplying a R = 10 Ω DC load. The supply systemis 440 VLL and 60 Hz. A) What is the value of the average (DC) current across the load?B) Compute the value of an inductive filter (L) to be added in series with the resistiveload to limit the rms value of the lowest order current harmonic to 1% of the DC currentvalue. Note: 2 /[( 1)( 1)] Vdch = Vdc0 h − h + (in rms).

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS