Q9): If the pins D and C are subjected to single shear while pin at A is a double shear. The diameter of pin D and C are 1.5 in while the diameter of pin A is 1 in. Determine the shear stress at pins A,D and C. Also find the stress in the bar DC if its diameter is 0.5 in. 5 ft B |E 3 ft3 ft-3 ft- 600 lb

Q9): If the pins D and C are subjected to single shear while pin at A is a double shear. The diameter of pin D and C are 1.5 in while the diameter of pin A is 1 in. Determine the shear stress at pins A,D and C. Also find the stress in the bar DC if its diameter is 0.5 in. 5 ft B |E 3 ft3 ft-3 ft- 600 lb

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.9.3P: A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is...

See similar textbooks

Similar questions

BADLY NEEDED ANSWER ASAP Determine the shear stress (in Mpa) in the 20.75-mm-diameter pin at A that support the beam if P = 28.96 kN, a = 2.12 m, and b = 5.72 m. Round off the final answer to three decimal places.
Consider the wooden member subjected to a tensile load P = 11.00 kN. Determine the shear stress at the inclined section as shown.
A 5-mm thicc plate of steel is formed into the cross section shown in Fig. P8.13. Locate the shear center for the cross section. e Figure P13
The simply supported joist is used in the construction of a floor for a building. In order to keep the floor low with respect to the sill beams C and D, the ends of the joists are notched as shown. If the allowable shear stress is tallow = 350 psi and the allowable bending stress is sallow = 1500 psi, determine the height h that will cause the beam to reach both allowable stresses at the same time. Also, what load P causes this to happen? Neglect the stressconcentration at the notch.
2. The W360 x 262 section carries a vertical shear force of 650 kN. For this section, calculate:(a) the minimum shear stress in the web;(b) the maximum shear stress in the web and(c) the percentage of the vertical shear force carried by the web.
The pin-connected frame supports the loads P1 = 5 kN and P2 = 10 kN. Determine for an angle of α = o0 : (a) The normal stress in the bar EC of uniform cross-sectional area 15 x 10-5 m2 . (b) The shearing stresses in the 10 mm diameter pins at D and E if both are in double shear.
The horizontal bar shown is pinned at O and is supported with a helical springat L1 from O. L1=2m, L2=1m. The spring has 30 turns and the diameter of the wire usedis 20mm. The diameter of the spring is 125mm. Modulus of Rigidity = 83GPa. Determine the shear stress of the helical spring loaded as shown if w = 25kN/m.
(D) The pin used at B has an ultimate shear strength of 58 ksi. If a factor of safety of 2.5 is required, determine the allowable shear stress in this pin. in ksi (E) The pin used at B is a double shear pin connection. Determine the minimum pin cross-sectional area, and the corresponding minimum pin diameter that can be used at B. (Amin IN in.2 and dpin IN in.) (F) Determine the deformations in rods (1), (2), and (3) when load P equals Pmax from Letter C. ANSWERS in inch (G) Using the results from Letter F, determine the deflections of Joint B and Point D. ANSWERS in inch
Determine maximum shear stress
A T- section is the cross section of a loaded beam as shown.Given: U1= 20 kN/m; M1 = 100 kN-m; P1 = 120 kN a.) Draw the shear diagram using graphical solutionb.) Determine maximum shearing stress.b.) Determine the shearing stress at the junction of the T-section.
Help me determine Maximum shear stress
The lap joint is fastened by 5 one-inch diameter rivets. For P = 10 kips, determine (1.) the maximum shear stress in the joints, (2.) the maximum bearing stress in the rivets, and (3.) the maximum stress at section a-a.