Answer all the question Q1) A) Fill the following blanks;I- Misalignment of measuring instrument is called2- Applying a number of known physical inputs and reconding theresponse of the system is called-3. Gauge Blocks is -4 Tolerance zone is5. works on the principle of serew and nut.6- Temperature is a form of-errors.7- Precision is -8 vermier micrometer include9. - which is mean the capability of an instrument tomeasure minimum distance accurately.10-- is an error catsed by incorect positioning of thecye when reading a measurement.

1. Misalignment of measuring instrument is called Abbe's Error 2. Applying a number of known…

QI) A) Fill the following blanks 1- Misalignment of measuring instrument is called 2- Applying a number of known physical inputs and reconding the response of the system is called 3 Gauge Blocks is + Tolerance zone is 5 works on the principle of screw and nut. 6 Temperature is a form of-- 7- Precision is errors 8 vemier micrometer include - which is mean the capability of an instrument to measure minimum distance accurately 10- SYE wt is an error cased by incorrect positioning of the measurement

QI) A) Fill the following blanks 1- Misalignment of measuring instrument is called 2- Applying a number of known physical inputs and reconding the response of the system is called 3 Gauge Blocks is + Tolerance zone is 5 works on the principle of screw and nut. 6 Temperature is a form of-- 7- Precision is errors 8 vemier micrometer include - which is mean the capability of an instrument to measure minimum distance accurately 10- SYE wt is an error cased by incorrect positioning of the measurement

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter3: Job Planning, Benchwork, And Layout

Section3.1: Understanding Drawings

Problem 1RQ: Information such as tolerances and scale can be found in the________ of an engineering drawing.

See similar textbooks

Similar questions

For the following statements, answer True or False and explain the answer briefly. The tolerance of standard mass used must be smaller than the uncertainty of analytical balance to be calibrated.
1-The smallest change in the quantity will produce the observable change in the reading is called as a. Sensitivity o b. Range c. Accuracy O d. Resolution
A 150.00-mm sine bar is used to inspect a part angle that has a dimension of 35.0° ± 1.0°. The sine bar rolls have a diameter = 25.0 mm. A set of gage blocks is available that can form any height from 10.0000 mm to 199.995 mm in increments of 0.005 mm. All inspection is performed on a surface plate. Determine (a) the height of the gage block stack to inspect the minimum angle, (b) the height of the gage block stack to inspect the maximum angle, and (c) the smallest increment of angle that can be set up at the nominal angle size
Information such as tolerances and scale can be found in the________ of an engineering drawing.
What is the process of comparing an unknown quantity with another quantity taken as standard called? a. scaling b. scientific method c. scientific notation d. measurement
Kindly answer all the questions and show complete solution; then i will rate UPVOTE(LIKE) your posted answer. If you didn’t answer all the questions and incomplete, I will rate DOWNVOTE(DISLIKE) your posted answer. Thank you so much for your effort. QUESTION: Convert the following readings of pressure to kPa absolute, assuming that the barometer reads 760 mm Hg: (sample answer: 1,000 kPa) don't forget the (space) and the (,) round off to 2 decimal place The following readings of pressure: a. 36 cm Hg vacuum b. 69 psig c. 18 in. Hg vacuum d. 24 atm gage
When several measured values agree with one another, the values are said to be accurate neither accurate nor precise both accurate and precise precise
In order to measure the extension of perfection in the mesh, the method of skewness is used.
If a 5.5 kg weights are added to bourdon gauge the reading on the of the gauge should be (assuming no error ) Select one: a. none b. 0.171224 N/mm2 c. 171.22KN/m2 d. 0.01746 KG/mm2
The degree of closeness of the measured value to the true value is ..........
To which of the following geometric tolerance families does perpendicularly belong? Form Tolerance. Location tolerance. Profile tolerance. Orientation tolerance
The type of error present in a measurement system which has error values as 10,20,30,40,10, is said to be systematic error. Select one: True False