QI. B. In the single-phase half-wave rectifier shown below, assume that the load current iola is constant (load inductance L is very large). (i) Sketch the load voltage waveform vo for a = 90° and find its average value Vdc. (ii) For R = 10 2 find the average and rms values of the diode current id for a = 45°. V₁ (240 V rms) to KH + Vo L (large)

QI. B. In the single-phase half-wave rectifier shown below, assume that the load current iola is constant (load inductance L is very large). (i) Sketch the load voltage waveform vo for a = 90° and find its average value Vdc. (ii) For R = 10 2 find the average and rms values of the diode current id for a = 45°. V₁ (240 V rms) to KH + Vo L (large)

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is CEMF?
What is the difference between a diode and rectifier?
Consider the full-wave rectifier circuit shown below, where• vS(t) is a sinusoidal signal with a peak value (Vs = 5 V).• Diodes are modelled using constant voltage model with VDO = 0.7 V• The ac line voltage has an rms value of 120 V and a frequency (f) = 60 Hza) Calculate the transformer turns ratio. b) Plot in the same graph signal vS(t) and the output signal vO(t) versus time (t) (show all details including amplitudes, time instances, etc.) c) Calculate the rms value of the output signal vO(t). (hint: sin2(x) = 0.5(1- cos(2x))) d) If a capacitor C=3.58 F is connected across R = 10 k, repeat (b) in a new graph
Q.1 A single-phase diode bridge rectifier is connected to a grid with rms voltage V, 230V at 50 Hz. Assume that the load is highly inductive, so it could be represented by a constant dc current, Id = 10A. a) Sketch the load voltage and find the average voltage of the load? b) Sketch the source current (grid. AC side) and find the rms value of the source current? c) Determine the fundamental source current and the first three harmonics? Assume Ish_rms ³ 0.91a/h for odd hand 0 otherwise?
The secondary input voltage to a single phase diode bridge rectifier is 50V, 50Hz, and the load can be replaced by a resistance of value 20ohms (a) Sketch a well labelled circuit of the converter described above. (b) Sketch the waveforms for the input voltage, output voltage, output current, and output current (c) Derive an equation for average output voltage and calculate for output dc voltage (d) Calculate the ripple factor of the output voltage (e) Transformer utilization factor (h) How can the ripple be improved
Q ) For the full- wave uncontrolled rectifier circuit supplying a series resistive Thesupply voltage is v =300 sinωt , the supply frequency is 50 Hz and the loadparameter values are: R =05 Ω,a) Sketch the diagram of electrical circuitb) Sketch the load voltage and current waveforms .c) Calculate the load currentd) Calculate the average DC load voltage Vdc .e) Calculate the supply power to the loa
please solve parts d and e Q.1 A single-phase diode bridge rectifier is connected to a grid with rms voltage V, 230V at 50 Hz. Assume that the load is highly inductive, so it could be represented by a constant dc current, Id = 10A. a) Sketch the load voltage and find the average voltage of the load? b) Sketch the source current (grid. AC side) and find the rms value of the source current? c) Determine the fundamental source current and the first three harmonics? Assume Ish_rms ³ 0.91a/h for odd hand 0 otherwise? d) Determine the input power (active)? e) Determine the power factor?
A single-phase fully controlled, full-wave, bridge rectifier has a source of 220 V rms at 50 Hz. The firing angle α = 45˚ and the current extinction angle β =255˚; (i) Determine whether the current is continuous or discontinuous and write the condition. (ii) Sketch the appropriate load voltage and load current waveform. (iii) If the firing angle is increased into 110˚, state the polarity of voltage and power for that condition.
A single-phase fully controlled, full-wave, bridge rectifier has a source of 230 V rms at 50 Hz, and is feeding a load R = 25 and L = 10 mH. The firing angle α = 45˚ and the current extinction angle β =230˚. It is required to: (a) Sketch the appropriate load voltage and load current waveforms. (b) Determine whether the current is continuous or discontinuous. (d) Determine the average load voltage and current. (e) Determine the rms load voltage and current. (f) Determine the a.c. and d.c powers absorbed by the load. (g) Determine the efficiency of the converter.
Calculate the rms load current for the single phase uncontrolled half-wave rectifier when the source voltage of 200V at a frequency of 50Hz, and load resistance is 10ohm.
(Q1 ,b) Required Explain the applications-based comparison b/w FWBR & CT-FWR so that under what conditions you will choose the CTWR.? b. Interpret (using the circuit diagram & the waveform diagrams) the behavior of a controlled Half-Wave Rectifier during the negative half cycle of AC supply when it is connected with RL load in the following cases; a. Without Free-wheeling diode.