Que 5.15. Fig. 5.15.1 shows a steel rod of 12 mm diameter with one end fixed into a horizontal table. The remainder of the rod is bent into the form of three quarters of a circle and the free end is constrained to move vertically. Determine the vertical deflection for a load of 10 kg. E = 208,000 N/m2.

Que 5.15. Fig. 5.15.1 shows a steel rod of 12 mm diameter with one end fixed into a horizontal table. The remainder of the rod is bent into the form of three quarters of a circle and the free end is constrained to move vertically. Determine the vertical deflection for a load of 10 kg. E = 208,000 N/m2.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Fbd ,formula and calculation should be included. Please work it fast without wasting a time. 1)The rod ABC is made of an aluminum for which E = 70 GPa. Knowing that P = 9 kN and Q = 14 kN, determine the deflection of: (a) Point A, (b) Point B. Consider upward to be positive.
The rod ABC is made of an aluminum for which E = 71.15 GPa. Knowing that P=10.2 kN and Q=51.62kN, determine the deflection (in um) of point B y=0.46 and z=0.56. Round off the final answer in four decimal places.
A single axial load of magnitude P is applied at end C of the steel rod ABC. Knowing that E = 30 × 106 psi, the deflection of point C will be 0.1 in. Determine the diameter of portion BC in inches if P = 50 kips.
Both portions of the rod ABC are made of an aluminum for which E = 70.4GPa. Knowing that the magnitude of Q is 31876 N, m = 0.35 m, and n = 0.55 m, determine the value of P (in N) so that the deflection at A is zero.
The rod ABC is made of an aluminum for which E = 71.4 GPa. Knowing that P = 7.94 kNand Q = 49.88 kN,determine the deflection (in μm) of point B if y = 0.47 and z = 0.54. Round off the final answer in four decimal places.
A vibration isolation unit consists of two blocks of hard rubber with a modulus of rigidity G= 19 MPa bonded to a plate AB and to rigid supports as shown. Denoting by P the magnitude of the force applied to the plate and by δ the corresponding deflection, determine the effective spring constant, k 5 P/δ, of the system.
A 4-ft section of aluminum pipe of cross-sectional area 1.75 in2 rests on a fixed support at A. The 58-in.-diameter steel rod BC hangs from a rigid bar that rests on the top of the pipe at B. Knowing that the smodulus of elasticity is 29 3 106 psi for steel and 10.4 3 106 psi for aluminum, determine the deflection of point C when a 15-kip force is applied at C.
Aluminum [E= 70 GPa] member ABC supports a load of 28 kN. Determine: (a) the value of load P such that the deflection of joint C is zero.(b) the corresponding deflection of joint B.
Q/Two hard rubber blocks [G = 280 kPa] are used in an anti-vibration mount to support a small machine as shown. Determine the downward deflection that will occur for an applied load of P = 860 N. Assume a = 14 mm, b = 50 mm, and c = 80 mm. The answer in mm?
A 7/8-in.-diameter rod BC is attached to the lever AB and to the fixed support at C. Lever AB has a uniform cross section 38 in. thick and 1 in. deep. For the loading shown, determine the deflection of point A. Use E=29 *106 psi and G=11.2 *106 psi.
Each of the links AB and CD is made of aluminum and has a cross-sectional area of 0.19 sq.in. Knowing that they support the rigid member BC, determine the downward deflection (in inches) of point E. if x = 12 in, y = 28.8 in, z = 21 in, E = 10817638 psi, and P = 35 kips. Round off the final answer to five decimal places.
A column of 3-m effective length is to be made by welding together two C130 *13 rolled-steel channels. Using E= 200 GPa, determine for each arrangement shown the allowable centric load if a factor of safety of 2.4 is required.