Question 1 The wheel of radius 300mm is being stopped by a block brake shown in the figure. A triangular distributed load is being applied to da d3 200mm 150mm the handle. With a coefficient of friction of 0.9, determine the smallest distributed load P 75mm necessary to resist an 85 N-m moment M. P=3620 N/m 25 mm

Question 1 The wheel of radius 300mm is being stopped by a block brake shown in the figure. A triangular distributed load is being applied to da d3 200mm 150mm the handle. With a coefficient of friction of 0.9, determine the smallest distributed load P 75mm necessary to resist an 85 N-m moment M. P=3620 N/m 25 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.3.20P: The hoisting arrangement for lifting a large pipe is shown in the figure. The spreader is a steel...

See similar textbooks

Similar questions

The piston in an engine is attached to a connecting rod AB, which in turn is connected to a crank arm BC (see figure). The piston slides without friction in a cylinder and is subjected to a force P (assumed to be constant) while moving to the right in the Figure. The connecting rod. with diameter d and length L, is attached at both ends by pins. The crank arm rotates about the axle at C with the pin at B moving in a circle of radius R. The axle at C, which is supported by bearings, exerts a resisting moment M against the crank arm. (a) Obtain a formula for the maximum permissible force Pallow. based upon an allowable compressive stress acin the connecting rod. (b) Calculate the Force Pallowfor the following data:
A bungee jumper having a mass of 55 kg leaps from a bridge, braking her fall with a long elastic shock cord having axial rigidity EA = 2.3 kN (see figure). If the jumpoff point is 60 m above the water, and if it is desired to maintain a clearance of 10 m between the jumper and the water, what length L of cord should be used?
Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.
The hoisting arrangement for lifting a large pipe is shown in the figure. The spreader is a steel tubular section with outer diameter 70 mm and inner diameter 57 mm. Its length is 2.6 m, and its modulus of elasticity is 200 GPa. Based upon a factor of safety of 2.25 with respect to Euler buckling of the spreader, what is the maximum weight of pipe that can be lifted? (Assume pinned conditions at the ends of the spreader.)
Solve the preceding problem for W = 1.0 lb. h = 12 in.,and k =0.511,/in.
The wheel of radius 300mm is being stopped by a block brake shown in the figure. A triangular distributed load is being applied to the handle. With a coefficient of friction of 0.9, determine the smallest distributed load P necessary to resist an 85 N-m moment M.
The shaft, is driven by pulley B from an electric motor. Another belt drivefrom pulley A is running a compressor. The belt tensions for pulley A are 1500 N and 600 N. The ratioof belt tensions for pulley B is 3.5. The diameter of pulley A is 150 mm and the diameter of pulley B is 480 mm. The allowable tensilestress for the shaft material is 170 MPa and the allowable shear stress is 85 MPa. Taking torsion andbending factors as 1.25 and 1.75 respectively, find the shaft diameter.Also find out the dimensions for a hollow shaft with outside diameter limited to 30 mm. Compare theweights of the two shafts. [Ans. 30 mm ; 24 mm ; 1.82 Given Length CD=350mm Length AB=150mm Length BD=100mm The total length is CD =350
As shown in the figure, a homogeneous 100-kgrigid block is suspended by the three springs whoselower ends were originally at the same level. Eachsteel spring has 24 turns of 10-mm-diameter on amean diameter of 100 mm, and G = 83 GPa. Thebronze spring has 48 turns of 20-mm-diameterwire on a mean diameter of 150 mm, and G = 42GPa. Compute the maximum shearing stress ineach spring using A.M. Wahl formula.
A damper square mat is supporting a dead load weight of8 kN. Helical springs will be used to support the loadlocated at all corners with shearing stress of 120.6 Mpaat 20 turns. The spring has a deformation of 98.7 mmwith a mean radius of 80 mm. Design the minimumdiameter of the wire to support a load. Use G = 83 Gpa.
(2) A single square thread jackscrew has 2.0TPI. It is to lift 15 tons. The friction radius of the collar is 1-in. The coefficient of friction between the threads and screws and base is 0.15, that between the screw and collar is 0.13. Determine: (a) the diameter of the root of the screw if the allowable stress in compression is 6,000psi; (b) the pull required at the end of 5.0ft bar to raise the load; (c) the twisting moment exerted at the root of the threads; (d) the efficiency of the screw and collar.
Hoop stress is limited to (2.4)MPa and density of flywheel material is (7504) Kg/m3
What is the maximum possible value of theclamping force C in the jaws of the pliers shown inthe figure if the ultimate shear stress in the 5-mmdiameter pin is 340 MPa?What is the maximum permissible value of theapplied load P to maintain a factor of safety of 3.0with respect to failure of the pin?