Question 10For the controlled half wave rectifier shown below; assume ideal thyristor: (No drop voltages)R1D12N1599R2if the source voltage is V 81 sin 76 t V, the load R111 QR2= 5 kn and the trigger current is 2mAfind the average voltage across the load.

Use Ohm’s law and calculate the gate turn-ON voltage,

Answered: Question 10 For the controlled half…

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is CEMF?
Single phase half sinusoidal wave controlled rectifier with (? = 30?) pure resistive load (Vs =220 v. f=60 Hz, R=10Ω) Determine the average output voltage Vo  Determine the r.m.s value of the output voltage
Calculate the rms load current for the single phase uncontrolled half-wave rectifier when the source voltage of 200V at a frequency of 50Hz, and load resistance is 10ohm.
Derive the average and RMS output voltage for three phase half controlled rectifier with RLE Load or three phase semi converters.
1. A single-phase, 120V, 50Hz supply is connected to a controlled half-wave thyristor rectifier and series R-L load consisting of a resistor R of 350 ohms and inductor L of 150mH. The thyristor firing angle is 65 degrees. Assume the diode and thyristor are ideal. i) calculate the dc load voltage VDC and the load dc current IDC. ii) briefly explain why a freewheeling diode is often connected in parallel to an R-L connected load in rectifier circuits
the three phase half wave uncontrolled rectifier is operated from 500v,50Hz supply at secondary side and the load resistance is 25 ohms. if the source inductance is negligible, determine a) rectification efficiency b) form factor c) ripple factor d) transformer utilization factor e) peak inverse voltage of each diode
The secondary input voltage to a single phase diode bridge rectifier is 50V, 50Hz, and the load can be replaced by a resistance of value 20ohms (a) Sketch a well labelled circuit of the converter described above. (b) Sketch the waveforms for the input voltage, output voltage, output current, and output current (c) Derive an equation for average output voltage and calculate for output dc voltage (d) Calculate the ripple factor of the output voltage (e) Transformer utilization factor (h) How can the ripple be improved
An ohmic resistive load connected to the output of a single phase uncontrolled full-wave (with diode) AC / DC rectifier and the output voltage average value Va is obtained. Same resistance single phase full wave, controlled (with thyristor) AC / DC was connected to the output of the rectifier and the average value Vb of the output voltage was obtained. Va = 1.7 Vb Find the trigger angle of thyristors.
A single-phase full-wave rectifier uses a power transformer whose secondary voltage is 220V r.m.s. The load resistor is 100kΩ. Neglect the transformer losses and the forward drops in the diodes. Determine the following: DC output voltage 2. Ripple voltage
A three-phase, half-wave uncontrolled rectifier is fed from an ideal three-phase voltage source of 380V, 50 Hz. The load is resistive with R=15 2. Calculate: (a) The average output voltage and average load current of the rectifier. (b) The d.c. and a.c. power dissipations in the load. (c) The diode ratings. (d) What is the lowest ripple frequency of the output voltage waveform?
Explain the firing angle range in the half-wave and full-wave controlled rectifier circuits feeding theRL load depending on the load characteristic.

SEE MORE QUESTIONS

Recommended textbooks for you

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Question 10 For the controlled half wave rectifier shown below; assume ideal thyristor: (No drop voltages) R1 D1 2N1599 R2 if the source voltage is V 81 sin 76 t V, the load R1 11 Q R2= 5 kn and the trigger current is 2mA find the average voltage across the load.